CategoryL1: Power Transmission

Products with this attribute (678 total)

Aignep USA 5/2 Single Solenoid Valve, Ext Pilot Spring Return 1/8 NPTF, 12V DC/3W Coil, LED Conn.

Air Cylinder, Air Cylinder, Double Acting, Air Cylinder Bore Dia. 12 mm, 80 mm Stroke, ISO, Double End Air Cylinder Mount, Stainless Steel Body Material, M5 x 0.8 in Port Size, 14 Degrees to 140 Degrees F Temp. Range, 185 mm Overall Length, Non-Magnetic Piston Material, 145 psi Max. Pressure, Hard Coat Anodized Finish, Aluminum End Cap Material, Stainless Steel Piston Rod Material, Magnetic Piston No, Tie Rod Material N, Tube Material Stainless Steel, Nose Mount Thread M16 x 1.25 in

Air Cylinder, Body Material Stainless Steel, Cylinder Type Round Body, Cylinder Repair Non-Repairable, Magnetic Piston Magnetic Piston, Mounting Type Pivot, Bore Diameter 1 1/2 in, Cushion Type None, Stroke Length 9 in, Inlet Size 1/8 in, Air Inlet Type NPT, Spring Retraction Force Not Applicable, Cylinder Action Double Acting, Number of Rods Single Rod, System of Measurement Inch, Body Material Finish Anodized, Piston Rod Material Finish Chrome Plated, Tie Rod Material Not Applicable

Air Safety Valve, Hard Seat, (M)NPT Inlet (In.) 1/2 in, Preset Setting (PSI) 225 psi, 459 cfm Rated CFM @ Set Pressure, Max. Temp. (F) 400 Degrees F, Brass Body Material, Stainless Steel Seal, Stainless Steel Ball, Stainless Steel Spring, Brass Seat, Vibra Seal Thread Coating, Standards ASME, CRN, NATIONAL BOARD, Compressed Air Safety Relief, High Temp

All Bestorq belts are designed to perform at the identical or higher level than all other major Manufacturer's belts of the same type. The outer fabric wrap is treated with highly oil and heat resistant, engineered synthetic rubber compound, specifically compounded for excellent wear resistance, proven through thousands of hours of testing. Top Width: 17.72 inches Material: Rubber Number of Ribs: 1 Pitch Length: 102 inches Depth: 0.09 inches Oil and Heat resistant

All Bestorq belts are designed to perform at the identical or higher level than all other major Manufacturer's belts of the same type. The outer fabric wrap is treated with highly oil and heat resistant, engineered synthetic rubber compound, specifically compounded for excellent wear resistance, proven through thousands of hours of testing.Top Width-5/8 inMaterial-Kevlar (Aramid)Inside Length-171.5 inOutside Length-175 inHeight-35/64 inNumber of Ribs-819.46Oil and Heat resistant

All Bestorq belts are designed to perform at the identical or higher level than all other major Manufacturer's belts of the same type. The outer fabric wrap is treated with highly oil and heat resistant, engineered synthetic rubber compound, specifically compounded for excellent wear resistance, proven through thousands of hours of testing.Top Width-5/8 inMaterial-Kevlar (Aramid)Inside Length-232.5 inOutside Length-236 inHeight-35/64 inNumber of Ribs-413.12Oil and Heat resistant

All Bestorq belts are designed to perform at the identical or higher level than all other major Manufacturer's belts of the same type. The outer fabric wrap is treated with highly oil and heat resistant, engineered synthetic rubber compound, specifically compounded for excellent wear resistance, proven through thousands of hours of testing.Top Width-5/8 inMaterial-Kevlar (Aramid)Inside Length-276.5 inOutside Length-280 inHeight-35/64 inNumber of Ribs-623.35Oil and Heat resistant

All Bestorq belts are designed to perform at the identical or higher level than all other major Manufacturer's belts of the same type. The outer fabric wrap is treated with highly oil and heat resistant, engineered synthetic rubber compound, specifically compounded for excellent wear resistance, proven through thousands of hours of testing.Top Width-5/8 inMaterial-RubberOutside Length-121 inHeight-35/64 inNumber of Ribs-69.95Oil and Heat resistant

ALUM MPL,1 DROP

Aluminum Electrolytic Capacitor, Polarized, Aluminum (Wet), 25V, 20% +Tol, 20% -Tol, 68000Uf, Chassis Mount

Angle Seat Valve Vzxf-L-M22C-M-A-N1-230-H3B1-50-16 Pneumatically Actuated Angle Seat Valve In Red Brass. Over Seat Version, Safety Position Closed, Npt Thread, Nominal Width 1". Design Structure=Poppet Valve With Piston Actuator, Type Of Actuation=Pneumatic, Sealing Principle=Soft, Assembly Position=Any, Mounting Type=Line Installation

Assembly, Pendant w Fittings, For Use With Mfr. Model Number MLK-AL269C, Fits Brand Ingersoll Rand

AUTO PAC 2 DROP,FREQ

AUTOMATION PAC

Axial Kit Eamm-A-T42-57A Nominal Length=43 Mm, Assembly Position=Any, Max. Speed=8000 1/Min, Storage Temperature=-25 - 60 ?C, Relative Air Humidity=0 - 95 %

B7015X2TADULEP7

Backstop,Metal

Baldor Motor, 3/4 HP, 1P, L1307M

Ball Insert Brg - 1.375 In Id X 2.8346 In Od X 1.3386 In W; Set Screw

Ball Insert Brg - 2.6875 In Id X 4.9213 In Od X 2.937 In W; Set Screw

Banded version of Super Power-Wedge? v-belt. Belt whip and turnover are minimized.

BCR-1-1/4-B

Beam Coupling,4 Beam,1/8 In.x3mm,Aluminum

Beam Coupling,4 Beam,12x9mm,303 SS

Beam Coupling,4 Beam,7mmx1/4 In.,Aluminum

Beam Coupling,6 Beam,14mmx5/16 In.,303 SS

Beam Coupling,6 Beam,15x13mm,Aluminum

Beam Coupling,6 Beam,17x13mm,303 SS

Belt, A/4L, 1/2 x 33.5 in. OC

Bestorq Timing Belt Model 1225-5M-100 - 48.23 in Outside Length - 3.94 in Top Width

Bestorq Timing Belt Model 2590-14M-75 - 101.97 in Outside Length - 2.95 in Top Width

Body Manifold Gun Pneumatic Valve Manifold

Both Ends Threaded Linear Shaft, For Use With -, System of Measurement Inch, Surface Roughness 16 uin

Brass Hose Barb Fitting, Connector, 3/16 Inch Barb X 1/4 Inch NPT Male End, PK 100

Cam Follower, Metric - Eccentric, #CFE101VUU

Cam Follower, Metric - Eccentric, #CFKRE40VR

CCF9/16SB

CCS7 Replacement/Interchange Hydraulic Filter

Chain & Cable Fluid, 12/Pump Spray, 12PK

CHECK RETAINER (VITON)

CLC-24-24-SS

Clip Bearing, Bore Diameter 9 mm, Flange Type Double Flange, For Housing Bore Range 10.6 to 10.87 mm, For Material Thickness Range 1.45 to 2.34 mm, For Shaft Size 8.975 to 9 mm, Material Group Plastic, Maximum PV 3,400 lb/sq in-fpm, Number of Flanges 2, Outside Diameter 14 mm, Overall Length 3.6 mm, Plain Bearing Material iglide Polymer, System of Measurement Metric, Application For Fitting Shafts Through Sheet Metal, Color Anthracite, Flange Thickness 0.8 mm, Large Flange Diameter 14 mm

CMB.F/R AID PISTON 1/8

COAL AID FIL 3/8,YELLOW

COAL FILTER 1/4 W/MTL BWL

COALESCENT FILTER

COMB AID 3/8,MTL,PNUT,BSP

COMB AID FIL REG 1/4 S VL

COMB AID FIL-REG LUB 1/4

COMB F-R 3/8,P-NUT,BSPP

COMB FIL REG 3/4

COMB FIL-REG 1/2

COMB FIL-REG DIA. 'E5'

Compact Cylinder Adn-80-10-I-P-A Per Iso 21287, With Position Sensing And Internal Piston Rod Thread Stroke=10 Mm, Piston Diameter=80 Mm, Piston Rod Thread=M12, Cushioning=P: Flexible Cushioning Rings/Plates At Both Ends, Assembly Position=Any

Compact Cylinder ADVUL-16-20-P-A

Compact Cylinder AEVU-20-25-A-P-A

Compact Cylinder Aevuz-16-15-P-A For Proximity Sensing, Piston-Rod End With Female Thread. Stroke=15 Mm, Piston Diameter=16 Mm, Cushioning=P: Flexible Cushioning Rings/Plates At Both Ends, Assembly Position=Any, Mode Of Operation=(* Single-Acting, * Pulling Action)

Compact Cylinder,40mm Bore,100mm Strke

Compressor Lubricant,MIN 32,1 gal.,PK4, Package Quantity 4

Compressor Oil,Drum,55 gal.,12.80 cSt

Compressor Oil,Pail,5 gal.,33.20 cSt

Coupling Piece KSG-M12X1,25

CRBS1408VT1

Crimp-style 77 Series hydraulic hose fittings

Cross Roller Bearing, Caged, #CRBC50050C2

Cross Roller Bearing, Full Complement, #CRB50050C2

Cross Roller Bearing, Mounting Holed, #CRBF9025ATC1

Cross Roller Way, Standard, #CRW241200

Cross Roller Way, Standard, #CRW4400SL

Cylindrial Roller Bearing. full complement > 120 mm <= 200 mm

D1360-8M-85 DAndD Powerdrive Timing Belt

D364XL050 DAndD Powerdrive XL Double Replacement Timing Belt

D385H001 DAndD Powerdrive H Double Replacement Timing Belt

D387L100 DAndD Powerdrive L Double Replacement Timing Belt

D720-8M-85 DAndD Powerdrive Timing Belt

D788L037 DAndD Powerdrive L Double Replacement Timing Belt

D850-5M-09 DAndD Powerdrive Timing Belt

DIA REG 1/4 BSPP,0-50

Double U-Joint, 3/4" x 7/16" Bores, 1.245" OD, Stainless

DPB SLOW START,MUFLER,BSP

Drilled Linear Rail, Overall Length 24.63 in, Overall Width 0.25 in, Overall Height 0.625 in, Rail Material Carbon Steel, Agency Compliance -, Dimension B1 -, Dimension F1 -, Dimension F2 -, Dimension G1 -, Dimension G2 -, Dimension J1 -, Dimension S3 -, Dimension X -, Dimension Y1/Y2 -, For Use With V-Guide Wheels and Bushings, Includes -, Maximum Operating Temperature 248 Degrees F, Minimum Operating Temperature 0 Degrees F, Mounting Hole Center to Center 3 in

E-Z Clip Field Attachable Fitting,17507

Easy Lock Brass Hose Fittings, Connectors, 3/8 Inch Hose Barb Splicer, PK 100

ELECTRONIC CONTROLLED MPL

Encoder Cable NEBM-M12G8-E-5-S1G9

Estate Mounting Hardware

EXT.REL PILOTED 1/2 BSPP

F/R-LUB ASSEMBLY