dataSource: amazonScraper

Products with this attribute (12868 total)

Voltage II - Inhibited Electrical Insulationg oils. These oils have desirable aquatic toxicity and carcinogenicity characteristics. Additional information is available upon request. Properties Test Method Typicals Standard Specification ASTM D 3487 Type II Viscosity, cSt @ 40?C ASTM D 445 9.3 Viscosity, cSt @ 100?C ASTM D 445 2.3 Specific Gravity, 15?C/15?C ASTM D 4052 .887 Pour Point, ?C ASTM D 97 -64 Color, ASTM D1500 0.5 Flash Point, COC, ?C ASTM D 92 155 Interfacial Tension @ 25?c, dynes/cm ASTM D 97 51 Aniline Point, ?C ASTM D 611 74.7 Dielectric Breakdown, kV ASTM D 1816 50 Power Factor, 25?C, % ASTM D 924 .005 Power Factor, 100?C, % ASTM D 924 .075 Oxidation Stability 72 hr: % Sludge by mass, <0.1 Total acid number, mg KOH/g <0.1 164 hr: % Sludge by mass, <0.1 Total acid number, mg KOH/g ASTM D 2440 <0.1 Oxidation Stability (Pressure Vessel), minutes ASTM D 2112 248 Oxidation Inhibitor Content, wt% AASTM D 2668 0.26 Corrosive Sulfur ASTM D 1275 B (modified version) Non-corrosive Water, ppm ASTM D 1533 9 Neutralization Number, mg KOH/g ASTM D 974 <0.01 PCB Content, ppm ASTM D 4059 ND Polycyclic Aromatic Compound, % (w/w) IP 346 <3 Modified Ames Assay ASTM E 1687 PassOxidation Inhibitor Content, wt% AASTM D 2668 0.26 Corrosive Sulfur ASTM D 1275 B (modified version) Non-corrosive Water, ppm ASTM D 1533 9 Neutralization Number, mg KOH/g ASTM D 974 <0.01 PCB Content, ppm ASTM D 4059 ND Polycyclic Aromatic Compound, % (w/w) IP 346 <3 Modified Ames Assay ASTM E 1687 Pass
WARNING : Under no circumstances should cam and groove couplings be used for compressed air or steam service.<br><br>Dixon Sanitary Cam and Groove Global Type C Adapters are Female Cam Coupler x Hose Shank fittings for transitioning your hose directly to a camlock connection. These Type C camlock fittings are available from 1/2" up to 4" in A380 Permanent Mold Aluminum or 316 Investment Cast Stainless Steel. Dixon cam fittings incorporate an extra long shank design that allows for proper banding, eliminating a major cause of hose damage.<br><br>Dixon camlock fittings are all precision machined to rigid tolerances and designed to be interchangeable with all products produced to Commercial Item Description A-A-59326B. However, no standard exists for the 1/2" and 8" fittings and generally these will not interchange with other manufacturers. All couplers, regardless of casting material, utilize durable stainless steel cam arm pins that will not rust or bind. The couplers also feature a recess to hold the gasket firmly in place, ensuring proper placement and eliminating any chance for leakage.<br><br>Cam and Groove fittings are designed for use as a hose coupling that allows quick connect capabilities to increase operator productivity. To secure a connection, simply slide the adapter into the coupler, and with normal hand pressure press the cam levers down. Uncoupling is just as simple, just lift the cam arms and remove the adapter. Dixon Sanitary also offers Dust Plugs and Dust Caps to keep hoses and process tubes clean while fittings are disconnected.<br><br>Dixon Cam and Groove Fittings Features:<br><br>- Precision Machined<br>- Rigid Tolerances<br>- Recessed Gasket Slots<br>- Buna N Seal Standard (alternates available)<br>- Stainless Steel Cam Arm Pins<br>- Interchangeable with most manufacturers
WARNING : Under no circumstances should cam and groove couplings be used for compressed air or steam service.<br><br>Dixon Sanitary Reducing Cam and Groove Female Cam Coupler x Male Cam Adapter for transitioning sizes between two camlock fittings. These camlock fittings are available from 1-1/2" up to 4" in 356T6 Aluminum or 316 Investment Cast Stainless Steel. The pressure rating for these fittings is based on the seal of the mating part.<br><br>Note: The 4" x 2" (4020-DA-SS) stainless steel fitting is produced as a welded fabrication.<br><br>Dixon camlock fittings are all precision machined to rigid tolerances and designed to be interchangeable with all products produced to Commercial Item Description A-A-59326B. However, no standard exists for the 1/2" and 8" fittings and generally these will not interchange with other manufacturers. All couplers, regardless of casting material, utilize durable stainless steel cam arm pins that will not rust or bind. The couplers also feature a recess to hold the gasket firmly in place, ensuring proper placement and eliminating any chance for leakage.<br><br>Cam and Groove fittings are designed for use as a hose coupling that allows quick connect capabilities to increase operator productivity. To secure a connection, simply slide the adapter into the coupler, and with normal hand pressure press the cam levers down. Uncoupling is just as simple, just lift the cam arms and remove the adapter. Dixon Sanitary also offers Dust Plugs and Dust Caps to keep hoses and process tubes clean while fittings are disconnected.<br><br>Dixon Cam and Groove Fittings Features:<br><br>- Precision Machined<br>- Rigid Tolerances<br>- Recessed Gasket Slots<br>- Buna N Seal Standard (alternates available)<br>- Stainless Steel Cam Arm Pins<br>- Interchangeable with most manufacturers