Label: ['HHIP']

Products with this attribute (47 total)

#30 NMTB ER-40 Collet Chuck-Drawbar End

0.052" Replacement Pin Gage P-0 -0.0002 Tolerance

0.122" Replacement Pin Gage P-1 -0.0002 Tolerance

0.324" Replacement Pin Gage P-2 0.0002 Tolerance

1-1/2 To 11-1/2 NPT High Speed Steel Taper Pipe Tap

1-1/2" D Plain Keyway Bushing

1/2" JT33 Drill Chuck with 5/8" Straight Shank Arbor

1/4-28NF H3 4 Flute High Speed Steel Taper Hand Tap

10 Piece Setting Masters Measuring Tools

18" Long Range Heavy Duty Dial Caliper

3/8-16 X 1" L Coupling Nut

4-3/8 X 2-3/8 X 1-1/8" Single Magnetic V-Block

4-40NC H2 3 Flute High Speed Steel Taper Hand Tap

<ul><li>?HHIP 8 X 6 X 5 open end slotted angle plate has convenient clamping slots for mounting.</li><li>?The plate is widely used for machining, layout and inspection</li><li>?It is made of high tensile cast iron properly seasoned against distortion and accurately machined to .002 per 6"</li><li>?The plate is square and parallel on all faces and Slot A is 90? to slot C</li><li>?1-2-3 precision matched pair block set is heat treated and case hardened to HRC 55 to 60</li><li>?They are also hardened and precision ground on all 6 sides of each block.</li><li>?The 1-2-3 blocks accuracy with squareness on all sides within .0002" per inch.</li><li>?There are 23 holes consisting of 5 tapped holes that are 3/8"-16 for clamping and 18 untapped holes.</li><li>?These blocks have a cross drilling design gives minimum weight and maximum strength.</li></ul>

<ul><li>?HHIP Sensitive Hand Drill Feed & 1/8" Keyless Drill Chuck</li><li>?The drill feed has a 1/2" diameter hardened and precision ground 0JT straight shank</li><li>?It allows for grasp free turning ring and feed drill</li><li>?The drill feed is spring loaded with 3/4" travel and fits any drill, mill, lathe or jig borer</li><li>?Using a hand drill feed reduces small drill breakage</li><li>?The drill feed and the drill chuck both have a TIR of .002"</li><li>?Included is a 0-1/8"/0-3mm JT0 keyless drill chuck</li><li>?This drill chuck is precision made with highest T.I.R. and has ultra-smooth bearings</li></ul>

DASQUA 0-1" DIAL INDICATOR WITH MAGNETIC BACK (5122-4211)

Dasqua 2-In-1 Laser Tape Measure 0.05-30M laser and 5M tape. OLED display. 2.5cm width tape. Measuring accuracy is +/-3mm. Li-on 3.7V battery. USB charging capability. Battery life is approximately 2000 measurements. Laser turns off automatically off after 30 seconds. Power turns off automatically after 90 seconds.

GB70-85 M4 X 16 Screw

Hhip CaratX3-8" Single Point Diamond Dresser 3900-0074 ZO-G2470449 - SIM Supply

Hhip Mini E-Z Hand Tapper 3900-0252 ZO-G2515443 - SIM Supply

Hhip Mount 4" 4-Jaw Scroll Lathe Chuck 5C 3900-4711 ZO-G4598354 - SIM Supply

Hhip Open End Slotted Angle Plate 12X9X8 3402-0212 ZO-G2455049 - SIM Supply

Hhip Pack Of E200 Replacement Blades 10pcs 2001-2252 ZO-G2469898 - SIM Supply

Hhip Piece Pin Gage Set 55 0.21-1.29Mm,-.005 4101-1011 ZO-G2498668 - SIM Supply

Hhip Precision Granite Square 15X10X1.5" 4901-2706 ZO-G2495369 - SIM Supply

Hhip Replacement Pin Gage P-6 0.0002 Toleranc 4103-0839 ZO-G2506779 - SIM Supply

Hhip Replacement Pin Gage P-6 0.0002 Toleranc 4103-0897 ZO-G2507366 - SIM Supply

Hhip Replacement Pin Gage P-6 0.0002 Toleranc 4103-0913 ZO-G2507576 - SIM Supply

Hhip Replacement Pin Gage P-7 0.0002 Toleranc 4103-0923 ZO-G2507804 - SIM Supply

Hhip Round Collet 5C 27-64" 3900-1124 ZO-G2466486 - SIM Supply

Hhip Round Collet 5C 3-8" 3900-1121 ZO-G2466407 - SIM Supply

Hhip Sir0265K08 3-8" Mini Indexable Threading 2305-0375 ZO-G2516125 - SIM Supply

Hhip Tin Double End Center Cut End Mill 4Flut 5829-0250 ZO-G2481597 - SIM Supply

Hhip Tin Single End Center Cut End Mill 4Flut 5828-0626 ZO-G2481746 - SIM Supply

Piece C-Type Micrometer Set 4 0-4 In.

Screw Thread Micrometer Kit 0-1 In./0.001 In.