- mpn4P914
- brandname: Dayton
- manufacturername: Dayton
Attributes
| Key | Value |
|---|
| Agency Compliance | UL and CSA on Motor Only |
| Bearing Type | Sealed Ball Bearing (Mo. |
| Best Efficiency GPM @ H. | 4.4 gpm @ 112 psi ft |
| Best Efficiency Head | 112 ft |
| Case Pressure (Maximum) | 300 psi |
| Compatible Discharge Pi. | 1 in |
| Compatible Intake Pipe . | 1 1/4 in |
| Compatible with Media T. | Water |
| Discharge Rotation | 90 Degrees Increments |
| Discharge Type | NPT |
| Duty | Continuous |
| Duty Cycle | Continuous |
| Electrical Connection T. | Plug-In |
| Features | 100% Tested, 300 lb Cas. |
| Flow Rate @ 10 psi | 5.8 gpm |
| Flow Rate @ 100 psi | 4.5 gpm |
| Flow Rate @ 120 psi | 4.2 gpm |
| Flow Rate @ 140 psi | Not Applicable |
| Flow Rate @ 15 psi | Not Applicable |
| Flow Rate @ 160 psi | Not Applicable |
| Flow Rate @ 180 psi | Not Applicable |
| Flow Rate @ 20 psi | 5.6 gpm |
| Flow Rate @ 200 psi | Not Applicable |
| Flow Rate @ 220 psi | Not Applicable |
| Flow Rate @ 240 psi | Not Applicable |
| Flow Rate @ 260 psi | Not Applicable |
| Flow Rate @ 30 psi | 5.5 gpm |
| Flow Rate @ 40 psi | 5.4 gpm |
| Flow Rate @ 50 psi | 5.2 gpm |
| Flow Rate @ 60 psi | 5.1 gpm |
| Flow Rate @ 70 psi | 4.9 gpm |
| Flow Rate @ 80 psi | 4.8 gpm |
| Flow Rate @ 90 psi | 4.7 gpm |
| Frame | 56c |
| Frequency | 60 Hz |
| GPM @ 10 PSI | 5.8 |
| GPM @ 100 PSI | 4.4 |
| GPM @ 150 PSI | - |
| GPM @ 20 PSI | 5.6 |
| GPM @ 30 PSI | 5.4 |
| GPM @ 50 PSI | 5.2 |
| GPM @ 60 PSI | 5.1 |
| GPM @ 75 PSI | 4.8 |
| Height | 7 7/8 in |
| Horsepower | 1/2 hp |
| Housing Material | Cast iron |
| HP | 1/2 hp |
| Impeller Design | Regenerative Turbine |
| Impeller Material | Bronze |
| Impeller Type | Regenerative Turbine |
| Includes | Cast Casing with Bronze. |
| Inlet | 1-1/4 in |
| Inlet (In.) | 1-1/4 |
| Inlet Pressure | 200 psi |
| Intake and Discharge Si. | 1 1/4 in , 1 in |
| Intake Type | NPT |
| Item | Turbine Pump |
| Manufacturer Warranty L. | 1 yr |
| Manufacturers Warranty . | 1 yr |
| Max. Case Pressure | 300 psi |
| Max. Dia. Solids | 25 Microns |
| Max. Pressure | 300 psi |
| Max. Specific Gravity | 1 |
| Maximum Feet of Head | 700 ft |
| Maximum Flow Rate | 40 gpm |
| Maximum Media Temperatu. | 300 Degrees F |
| Maximum RPM | 3,450 RPM |
| Minimum Flow Rate | 2 gpm |
| Minimum Media Temperatu. | -20 Degrees F |
| Motor Enclosure | ODP |
| Motor Enclosure Broad | ODP |
| Motor Enclosure Type | ODP |
| Motor Frame Designation | 56c |
| Motor Type | Cap-Start, ODP |
| Mounting Orientation | Horizontal, Vertical |
| Nameplate Voltage | 115/230V AC |
| NPSHr | 200 psi |
| Number of Stages | 1 |
| Operation | Manual |
| Outlet | 1 in |
| Overall Height | 7.88 in |
| Overall Width | 6.75 in |
| Phase | 1 |
| Phase Broad | 1 |
| Port Rotation | 90 Degrees Increments |
| Pump Housing Material | Cast iron |
| Pump Housing Material B. | Ci |
| Seal Material | Buna, Carbon, Ceramic |
| Seal Type | Mechanical, O-Ring, Sea. |
| Series | T51 |
| Shut Off Pressure (Maxi. | 130 psi |
| Solid Diameter (Maximum) | 25 micron |
| Specific Gravity (Maxim. | 1 |
| Standards | AISI 304, AISI 316, AST. |
| Thermal Overload Protec. | Yes |
| Voltage | 115/230 |
| Wetted Material | Bronze Fitted, Cast Iron |
| Wetted Materials | Bronze Fitted, Cast Iron |
| Width | 6 3/4 in |