Brand name: Brand: WEG

Products with this attribute (38 total)

B007UU5XDW
B007UU6336
Close-Coupled Pump Motor, 3-Phase, 5 HP, Nameplate RPM 1745, Voltage 575, 3 Phase, Frame 184JM, Totally Enclosed Fan-Cooled, Full Load Amps 5.18, 60 Hz, Face/Base Mounting, Thermal Protection None, Insulation Class F, Service Factor 1.25, Regreasable Ball Bearings, Max. Ambient Temp. 40 Degrees C, CW/CCW Rotation, Overall Length 17 In., Shaft Dia. 7/8 In., Shaft Length 4-1/4 In., Frame Material Cast Iron.
Coil, 277VAC, 50-105 Amp
Contactor, 80A, 3-Pole, 208-240VAC coil (60Hz only)
Contactor, Mini, 7A, 3-Pole, 480VAC coil (60Hz) / 400-415VAC (50Hz), 1-NC Contact
Contactor, Mini, 9A, 3-Pole, 24VDC coil, 1-NC Contact
Contactor, Mini, 9A, 3-Pole, 480VAC coil (60Hz) / 400-415VAC (50Hz), 1-NC Contact
Enclosed Starter, 15hp@230V-3ph, 120VAC coil (60Hz) / 110V (50Hz), NEMA 1, Start/Stop, Reset
Enclosed Starter, 7.5hp@460V-3ph, 120VAC coil (60Hz) / 110V (50Hz), NEMA 4X, Start/Stop, Reset
GPH2 ENCLOSED SOFT STARTER 75HP 85A 460V AC3 HMI
Identifier, Terminal Block, Marking (31-40), 5x5mm
Identifier, Terminal Block, Marking (7), 6x5mm
In addition to a very small, easily mounted package; simplified keypad with a bright LED readout, complete diagnostics, and fully programmable I/O, the WEG CFW10 drive series controls 3-phase AC motors with a single phase AC input. <> Same programming as all other great WEG VFD's <> V/Hz control <> IP20 finger safe enclosure <> Single Phase 110-127V input voltage up to 1 HP <> Single Phase 200?240V input voltage up to 3 HP <> 150% current overload capacity <> 2.5-15 kHz adjustable switching frequency <> Four isolated programmable digital inputs (12vdc) <> Programmable relay output (250vac 0.5A/125vac 1.0A or 30vdc 2.0A) <> One isolated programmable analog input (0-10V 0/4-20mA) <> Diagnostic features: Over current, motor overload, drive over temperature, output short circuit, DC bus over and under voltage and external fault <> Control features: Linear and S-Ramp acceleration and deceleration, local / remote control, DC braking, torque boost, motor slip compensation, electronic pot, preset speeds, minimum and maximum adjustable frequency limits, adjustable output current limit, JOG <> Display readings: Motor speed, frequency, voltage, current, last fault, heatsink temperature and drive status <> Ambient: 122?F (50?C), 3300 ft (1000 m) altitude, 90% humidity, non-condensing <> 18-MONTH WARRANTY <> 36 months available with matched WEG motors.
Internal Jumper, 2 poles, Terminal Block BTWP 10
Legend, 30mm, "Down-Off-Up"
Legend, 30mm, "Fault"
Miniature Circuit Breaker, UL1077, 480VAC, B-Curve, 3-Pole, 2Amps
Miniature Circuit Breaker, UL1077, 480VAC, D-Curve, 3-Pole, 25Amps
Technical Specification: Close-Coupled Pump motor Application Pumps Motor Sub Application Waste Water Motor Type 3-Phase Enclosure Open Drip proof HP 25 Nameplate RPM 3530 Frame 256JP Rotation CW/CCW Voltage 575 Full Load Amps 23.4 Phase 3 Hz 60 Mounting Face/Base Bearings Ball Frame Material Cast Iron Thermal Protection None Service Factor 1.15 Max. Ambient Temp. 40 Degrees C Shaft Dia. 1-1/4 Shaft Length 8-1/4 Shaft Type JP Threaded Length Less Shaft 18-10/16 Overall Length 26-7/8 Insulation Class F RPM Range 3001-3600 Duty Continuous Nominal Efficiency 91.0% Efficiency Group High Inverter Rated Yes Standards UL Recognized, CSA Certified, CE Compliant.
Technical Specification: General Purpose motor Application General Application Motor Type 3-Phase Enclosure Open Drip proof HP 25 Nameplate RPM 3530 Frame 256T Voltage 575 Hz 60 Phase 3 Full Load Amps 23.8 Number of Speeds 1 Mounting Foot Mounting Position Horizontal Thermal Protection None Insulation Class F Service Factor 1.15 Bearings Ball Frame Material Cast Iron Max. Ambient Temp. 40 Degrees C Rotation CW/CCW Shaft Dia. 1-5/8 Shaft Length 4 Length Less Shaft 18-3/8 Overall Length 22-3/8 Shaft Type Keyed RPM Range 3001-3600 Standards UL, CSA, CE, NEMA MG-1 Part 31 Duty Continuous Efficiency Group NEMA Premium(R) Nominal Efficiency 91.7% 3 Green Certification or Other Recognition NEMA Premium Rated Green Environmental Attribute Product Contributes to Reducing Energy Consumption Compliance & Restrictions Compliance and Restrictions Green Product - This item has been designated by the manufacturer as an environmentally preferable product (EPP) because this item is NEMA Premium Rated. This listing is for each.
Technical Specification: General Purpose motor Application General Application Motor Type 3-Phase Enclosure Totally Enclosed Fan-Cooled HP 100 Nameplate RPM 3570 Frame 404/5TS Voltage Hz 60/50 Phase 3 Full Load Amps 110 Mounting Foot Mounting Position Horizontal Thermal Protection None Insulation Class F Service Factor 1.25 Bearings Ball Frame Material Cast Iron Max. Ambient Temp. 40 Degrees C Rotation CW/CCW Shaft Dia. 2-1/8 Shaft Length 4-1/4 Length Less Shaft 32-1/2 Overall Length 36-3/4 RPM Range 3001-3600 Standards UL, CSA, CE, NOM, NEMA Class 1, Div 2, Groups B, C & D Duty Continuous Efficiency Group Super Premium Nominal Efficiency 95.4% 3 Footnotes 20:1 CT & 1000:1 VT Green Environmental Attribute Product Contributes to Reducing Energy Consumption Compliance & Restrictions Compliance and Restrictions Green Product - This item has been designated by the manufacturer as an environmentally preferable product (EPP) because this item has one or more environmentally preferable attributes. For additional information, see the Tech Specs tab on the product description page. This listing is for each.
Technical Specification: General Purpose motor Application General Application Motor Type 3-Phase Enclosure Totally Enclosed Fan-Cooled HP 25 Nameplate RPM 1765 Frame 284T Voltage Hz 60 Phase 3 Full Load Amps 65.2-59.0/29.5 Number of Speeds 1 Mounting Base Mounting Position Horizontal Thermal Protection None Insulation Class F Service Factor 1.25 Bearings Ball Frame Material Cast Iron Max. Ambient Temp. 40 Degrees C Rotation CW/CCW Shaft Dia. 1-7/8 Shaft Length 4-5/8 Length Less Shaft 21-13/16 Overall Length 26-7/16 Shaft Type Keyed RPM Range 1701-1800 Standards UL, CSA, CE, NOM, NEMA Class 1, Div 2, Groups B, C & D Duty Continuous Efficiency Group High Efficiency and NEMA Premium(R) Nominal Efficiency 93.6% 3 Footnotes 23.
Technical Specification: General Purpose motor Application General Application Motor Type 3-Phase Enclosure Totally Enclosed Fan-Cooled HP 40 Nameplate RPM 1780 Frame 324T Voltage Hz 60/50 Phase 3 Full Load Amps 48.9 Mounting Foot Mounting Position Horizontal Thermal Protection None Insulation Class F Service Factor 1.25 Bearings Ball Frame Material Cast Iron Max. Ambient Temp. 40 Degrees C Rotation CW/CCW Shaft Dia. 2-1/8 Shaft Length 5-1/4 Length Less Shaft 24-3/8 Overall Length 29-5/8 RPM Range 1701-1800 Standards UL, CSA, CE, NOM, NEMA Class 1, Div 2, Groups B, C & D Duty Continuous Efficiency Group Super Premium Nominal Efficiency 95% 3 Footnotes 20:1 CT & 1000:1 VT Green Environmental Attribute Product Contributes to Reducing Energy Consumption Compliance & Restrictions Compliance and Restrictions Green Product - This item has been designated by the manufacturer as an environmentally preferable product (EPP) because this item has one or more environmentally preferable attributes. For additional information, see the Tech Specs tab on the product description page. This listing is for each.
Technical Specification: General Purpose motor Application General Application Motor Type 3-Phase Enclosure Totally Enclosed Fan-Cooled HP 50 Nameplate RPM 1775 Frame 326T Voltage Hz 60 Phase 3 Full Load Amps 131.0-118.0/59.2 Number of Speeds 1 Mounting Base Mounting Position Horizontal Thermal Protection None Insulation Class F Service Factor 1.25 Bearings Ball Frame Material Cast Iron Max. Ambient Temp. 40 Degrees C Rotation CW/CCW Shaft Dia. 2-1/8 Shaft Length 5-1/4 Length Less Shaft 25-7/8 Overall Length 31-1/8 Shaft Type Keyed RPM Range 1701-1800 Standards UL, CSA, CE, NOM, NEMA Class 1, Div 2, Groups B, C & D Duty Continuous Efficiency Group High Efficiency and NEMA Premium(R) Nominal Efficiency 94.5% 3 Footnotes 23.
Technical Specification: Hazardous Location motor Application Hazardous Locations Motor Type 3-Phase Enclosure Totally Enclosed Fan-Cooled HP 100 Nameplate RPM 1190 Frame 444T NEMA Design B Rotation CW/CCW Voltage Full Load Amps Phase 3 Hz 60 Mounting Foot Bearings Regreasable Ball Frame Material Cast Iron Thermal Protection T Stat Service Factor 1.15 Hazardous Location Class 1 C, D / 2 F, G Max. Ambient Temp. 40 Degrees C Temp. Code T3C Shaft Dia. 3-3/8 Shaft Length 8-1/2 Length Less Shaft 35-5/16 Overall Length 43-13/16 Insulation Class F RPM Range 1101-1200 Duty Continuous Nominal Efficiency 95.0% Efficiency Group NEMA Premium Standards UL Listed (E87848), CSA Certified (LR50962) Green Environmental Attribute Product Contributes to Reducing Energy Consumption Green Certification or Other Recognition NEMA Premium Rated Compliance & Restrictions Compliance and Restrictions Green Product - This item has been designated by the manufacturer as an environmentally preferable product (EPP) because this item is NEMA Premium Rated. This listing is for each.
Technical Specification: IEEE 841 motor Application IEEE Motors Motor Type 3-Phase Enclosure Totally Enclosed Fan-Cooled HP 125 Nameplate RPM 1800 Frame 444/5T Voltage 460 Hz 60 Phase 3 Full Load Amps 139 Number of Speeds 1 Mounting Foot Mounting Position Horizontal Thermal Protection None Insulation Class F Service Factor 1.15 Bearings Ball Frame Material Cast Iron Max. Ambient Temp. 40 Degrees C Rotation CW/CCW Shaft Dia. 3-3/8 Shaft Length 8-1/2 Length Less Shaft 36-7/16 Overall Length 45 Shaft Type Keyed RPM Range 1701-1800 Standards UL, CSA, CE, NOM, NEMA Class 1, Div 2, Groups B, C & D, NEMA MG-1 Part 31 Duty Continuous Efficiency Group NEMA Premium(R) Nominal Efficiency 95.4% 5.
Technical Specification: IEEE 841 motor Application IEEE Motors Motor Type 3-Phase Enclosure Totally Enclosed Fan-Cooled HP 30 Nameplate RPM 3535 Frame 286TS Voltage 460 Hz 60 Phase 3 Full Load Amps 33.8 Number of Speeds 1 Mounting Foot Mounting Position Horizontal/Vertical Thermal Protection None Insulation Class F Service Factor 1.25 Bearings Ball Frame Material Cast Iron Max. Ambient Temp. 40 Degrees C Rotation CW/CCW Shaft Dia. 1-5/8 Shaft Length 3-1/4 Length Less Shaft 23-5/16 Overall Length 26-9/16 Shaft Type Keyed RPM Range 3001-3600 Standards UL, CSA, CE, NOM, NEMA Class 1, Div 2, Groups B, C & D, NEMA MG-1 Part 31 Duty Continuous Efficiency Group NEMA Premium(R) Nominal Efficiency 91.7% Inverter Rated Yes 5.
Technical Specification: Power Factor Correction Capacitor KVAR 17.5 Voltage 480VAC Phase 3 Hz 60 Protection None Starts per Hour 30 Discharge Time 30 Seconds Temp. Range -25 Degrees to +55 Degrees C Terminals Box NEMA Enclosure Type 4 Height 23.7 Width 11.8 Depth 4.8 Standards UL Recognized (E346734).
Technical Specification: Vertical Pump motor Application Pumps Motor Sub Application Waste Water Motor Type 3-Phase Enclosure Totally Enclosed Fan-Cooled HP 15 Nameplate RPM 3500 Frame 215HP Rotation CW/CCW Voltage 230/460 Full Load Amps 38.0-34.4/17.2 Phase 3 Hz 60 Mounting Flange Mounting Position Vertical Bearings Regreasable Ball Frame Material Cast-Iron Finish Blue Enamel Base P-Base Thermal Protection None Service Factor 1.25 Ambient Temperature 40 Degrees C Shaft Dia. 1-1/8 Shaft Length 2-3/4 Length Less Shaft 17-3/8 Overall Length 21-3/8 Insulation Class F RPM Range 3001-3600 Duty Inverter Nominal Efficiency 90.2 Efficiency Group Epact Standards UL, CSA, CE NEMA Standard Inverter NEMA MG 1 Part 30: 100:1 Variable and 20:1 Constant Torque.
Technical Specification: Vertical Pump motor Application Pumps Motor Sub Application Waste Water Motor Type 3-Phase Enclosure Totally Enclosed Fan-Cooled HP 7-1/2 Nameplate RPM 3460 Frame 184HP Rotation CW/CCW Voltage 230/460 Full Load Amps 19.4-17.5/8.76 Phase 3 Hz 60 Mounting Flange Mounting Position Vertical Bearings Double-Shielded Ball Frame Material Cast-Iron Finish Blue Enamel Base P-Base Thermal Protection None Service Factor 1.25 Ambient Temperature 40 Degrees C Shaft Dia. 1-1/8 Shaft Length 2-3/4 Length Less Shaft 13-3/4 Overall Length 16-1/2 Insulation Class F RPM Range 3001-3600 Duty Inverter Nominal Efficiency 88.5 Efficiency Group Epact Standards UL, CSA, CE NEMA Standard Inverter NEMA MG 1 Part 30: 100:1 Variable and 20:1 Constant Torque.
Timing Relay, Electronic Off-Delay, 30-300s, 100-240VAC 50/60Hz/VDC
Variable Frequency Drive (VFD) by WEG: 2HP 4.3A 460V NEMA4X (Aka: ?AC Drive? or ?Motor Drive?).
WEG Electric CWM12-00-20V18, 2-Pole, 12 Amps, 110-120VAC Coil, IEC Contactor
WEG manufactures electric motors, controls, and coatings for industrial power distribution and automation. The company, founded in 1961, is headquartered in Jaragu? do Sul, Brazil.
WEG manufactures electric motors, controls, and coatings for industrial power distribution and automation. The company, founded in 1961, is headquartered in Jaragu? do Sul, Brazil.
WEG manufactures electric motors, controls, and coatings for industrial power distribution and automation. The company, founded in 1961, is headquartered in Jaragu? do Sul, Brazil.
WEG Minature Circuit Breaker, UL489 480VAC, C-Curve, 3-Pole, 1Amps