CategoryL1: ACTUATOR (Page 15)

Series CG1 precision air cylinder has 8 bore sizes and can meet any application need. The tube is impact extruded aluminum to produce an extraordinarily smooth finish, allow low break-away pressure and smooth stroke action. Eight mounting options are available. Auto switch capable.

Series CRB2, single or double vane type, rotary actuator is available in 10, 15, 20, 30 or 40 bore. The single vane style uses specially designed seals and stoppers which enable this compact type actuator to rotate up to 270. Direct mounting is possible for sizes 10 to 30 with the angle adjuster unit. The use of bearings to support thrust and radial loads, along with the implementation of an internal rubber bumper (except for size 10), makes the CRB2 excellent in reliability and durability. Other options include flange mounting, side or axial ports and auto switch capability.

Series CS1 air cylinder is SMCs largest bore cylinder. This series is available in bore sizes up to 12in. and stroke lengths up to 60in.. Additionally, the CS1 can be ordered auto-switch capable. Other options include, large bore sizes up to 12in. *, various mounting configurations, cushion for noise damping.

Series CXS is available in six bore sizes and stroke lengths up to 100mm. This series is very compact and has a very accurate non-rotating specification. It is suited for accurate pick-and-place applications or light duty material handling. The CXS can be used with either reed or solid state switches. Available in clean room versions.

Series NCJ2 miniature cylinders available in spring return, spring extend, or double acting all offer stainless steel tubing and stainless steel rods. Available in bore sizes 6, 10, 16mm and stroke lengths from 1/2in. to 8in.. Basic, foot, front flange and double rear clevis mounting options. Auto-switch capable. Other features include non-rotating, double rod, rubber bumpers and a stainless steel body.

SMC's E-MY2 series e-rodless actuators require no programming, and have both the operational ability of an air cylinder, and the speed controllability of an electric actuator.? The series consists of the E-MY2B (basic), E-MY2C (cam follower guide), E-MY2H (linear guide, single axis), and the E-MY2HT (linear guide, double axis) styles.? Offered in an integrated or remote control type, the E-MY2 is available with 3 or 5-point accurate stop options (2-points for both ends, with the remaining points for any preferred intermediate stops), and a wide selection of standard strokes, speed rates, and applicable loads.

SMC's LEP series of miniature electric actuators offer a high level of precision, accuracy and repeatability in a compact and lightweight design.? Small enough to fit in the palm of your hand, the miniature rod (LEPY) and miniature slide table (LEPS) come with selectable high pushing force, and/or compact and lightweight motor options.? By placing the motor in the axial direction, and reducing the width to 20.5mm and 21mm respectively, both models offer an ideal space saving solution.? The LEP series can be adapted for any application with up to 64 positioning points, and positioning repeatability of

SMC's pin clamp cylinder series C(L)KQ series was designed with 4 body types for a broad range of installation conditions. There are 55 types of guide pins available and an optional locking mechanism. C(L)KQ series has positioning and clamping at one time! Precision adjustment of clamping height is possible by choosing the with-shim type. Adjustment range: 0.5 to 3mm.

SMC's series CA2-Z air cylinder is 15% lighter than the existing CA2 cylinder.? Fine adjustment is now possible due to the increase in the air cushion?adjustment range.? The CA2-Z can now be ordered with rod end or pivot brackets, and mounting dimensions are the same as the existing CA2.? A variety of auto switches are available for mounting, including compact switches and magnetic field resistant switches.? The CA2-Z is available in 40, 50, 63, 80 and 100 bores sizes, and is RoHS compliant.

The C76 series air cylinders offer a simple, space saving design with high dimensional accuracy, making these cylinders very easy to use. Large spanner flats on the rod and head covers greatly simplify their installation and positioning. Low friction and the standard elastomer cushion rings allow piston speeds up to 1500mm/sec. Greater side loads are allowed due to the close tolerance of the piston rod in the front-end bush.

The C85 series conforms to ISO 6432 and CETOP RP52P. The C85 is available in bore sizes 8mm through 25mm with standard strokes ranging from 10mm through 300mm. A unique rod packing design prevents entry of dust and the effectiveness of the seal is such that the C85 is suitable for use in extremely dusty environments. With abrasion resistant packings and replaceable nose seals, the C85 offers exceptional service life.

The C95 is ISO, VDMA24562 interchangeable, and utilizes a tie rod construction. In addition to standard cushions and wear band, the C95 utilizes a "floating" cushion seal design that greatly improves operation. SMC's exclusive "figure 8" seal insures long cycle life.

The CE1 series is a stroke reading cylinder with position feedback. The home position can be anywhere within the cylinder stroke. Measurement is possible throughout the full stroke range. The CE1 series is offered in 6 bore sizes and is auto switch capable.

The CK1 series is a clamp cylinder available in two styles of clevis widths *. It is a non-lube, compact, lightweight cylinder with a built-in speed controller. Gaiters are unnecessary because a heavy-duty coil scraper is provided as a countermeasure against spatters. The CK1 is available in 3 bore sizes with stroke lengths up to 150mm. Options include rod attachments and auto-switch capabilities.

The compact design of series NCJP double acting pin cylinder minimizes mounting space. The NCJP is available in five mounting options to accommodate many design styles. Bore sizes include 6, 10 and 15mm with strokes ranging from 5 to 30mm. Other features include brass panel mounting nuts, stainless steel piston rod and brass bodies. The NCJP series is also available in an auto switch capable model.

The cost effective and clean looking AC series allows you to pick a combination of modular style air preparation equipment that best suits your needs. The series, available in 8 size options to ensure optimum performance, offers energy savings, with higher flow rates. Simple assembly and maintenance reduces downtime.

The CQS compact cylinder is available for those small bore cylinder applications where saving space is a concern. The CQS offers standard long strokes * in four bore sizes from 12 to 25mm. Long stroke versions incorporate a wear band and thicker piston to handle the increased bearing needs of the longer strokes. Both switch capable and non-switch capable body styles are the same, and switches can be mounted on three * and four * sides. An increased side load version * is available for more demanding applications.

The CRA1 rack & pinion rotary actuator offers very high torque-to-size and accurate positioning. Bore sizes are 30, 50, 63, 80 and 100mm. Units may be ordered auto-switch capable and with cushions. Dimensions range from 3" X 4" X 2" to a maximum of 8" X 9.65" X 4.41". Single shaft end or double shaft end models are available.

The CRA1 rack and amp; pinion rotary actuator offers very high torque-to-size and accurate positioning. Bore sizes are 30, 50, 63, 80 and 100mm. Units may be ordered auto-switch capable and with cushions. Dimensions range from 3" X 4" X 2" to a maximum of 8" X 9.65" X 4.41". Single shaft end or double shaft end models are available.

The LEF series slider type electric actuator features a low profile height of 46mm *. The actuators main body can be mounted without removing any exterior components, such as the cover, making installation easy. The standard equipped seal band covers the guide, ball screw and belt, preventing grease and external foreign matter from splashing and entering the LEF. There are 2 types of drivers available, ball screw or timing belt. Available motors include servo motor ball screw drive or step motor belt drive. When the LEF is ordered with the controller, initial data of the actuator is preset in the controller allowing start-up in a short time with the in.easy modein..

The MB series medium duty tie rod cylinder offers an improved design that enhances cylinder operation and ease of use. The standard air cushion utilizes a floating cushion seal to eliminate piston rod bouncing. The cushion volume has been elevated permitting about 30% more allowable kinetic energy absorption. The port and captive cushion adjustment valve are located on the same side of cap for heightened access. The MB series is available with many standard options, which include stroke adjustment, tandem, high/low temperature seals, heavy rod scraper, non-rotating rod, double rod and many more.

The MHZ2 series is a standard type parallel air gripper, taking the place of the MHQ*2 series. A linear guide provides high rigidity and high accuracy. MHZ2 can operate under higher pressure even at a larger holding point and overhang. High degree of mounting precision is achieved and mounting repeatability is improved.

The MY2 high precision guide cylinder is available in bore sizes 16mm, 25mm and 40mm. This series has been designed with a high precision single or double axis guide to create a compact, low profile cylinder. Maintenance has been simplified by allowing the cylinder to be detached without disturbing the guide unit and work piece.

The NCG provides precision mounting, short overall length, and high speed. Rubber bumpers are standard and an optional adjustable air cushion is available. Nine mounting styles include basic body, foot, single clevis, front or rear flange, front or rear trunnion, nose mount, and double clevis. Bore sizes range from 3/4in. to 2 1/2in. and standard stroke lengths from 1in. to 12in.. The NCG series is auto-switch capable. Non-rotating and double rod are standard options.

The NCRB single vane, double shaft style rotary actuator is available in 7 sizes (10-30mm). Rotation angles of up to 270 is possible for the entire series. The NCRB series offers smooth, step-free operation and long life expectancies in rugged service applications. Optional auto switches are available.

The new style MGP has a shorter guide rod and thinner plate resulting in a weight reduction of up to 17% over the original MGP.??The series is designed for high side load applications found in material handling, lifting and stopping. The?cylinder utilizes an ultra-compact design by incorporating the cylinder body as part of the guide body. As the stroke length increases, so does the bearing length, thus enhancing the cylinders load bearing capacity. The MGP offers higher load capability, longer strokes, 2 port locations, switch mounting grooves on two sides, and a more versatile T-slot mounting than the MGQ series.

The NRB shock absorber has a specially designed orifice that compensates for varying speeds and loads to consistently decelerate loads without requiring additional adjustment. The double seal enclosure consisting of a scraper and a rod seal, provides extra insurance against leakage. The NRB series shock absorbers are available in six sizes and all withstand an impact speed of 16 ft/sec.

The RSQ series is a fixed-height stopper cylinder with proven endurance and low breakaway characteristics. The RSG series is an adjustable mounting height stopper cylinder. It can be raised or lowered according to the distance required to stop the work piece. The RSH heavy-duty stopper cylinder is specially designed for use on conveyor lines or other applications requiring an external stopping device.

The ZCUK series is a non-rotating free mount cylinder for vacuum applications. The ZCUK was created by providing a vacuum passage in the rod of the CUK cylinder to enable a vacuum pad to be installed on the end of the rod. A guide is provided as standard equipment. Vacuum pads are available with pad diameters of 2 to 50. Cap or rod piping is available to the rod side. Series ZCUK is available in 5 bore diameters.

With English threads and NPT ports, the NCQ2 series is a versatile cylinder well suited to a variety of applications. The short overall length, of this space saving cylinder helps to make various jigs and equipment more compact. Snap rings are used to secure the head cover, making replacement of seals possible. For maximum flexibility, you can select double-rod end, non-rotating, and single acting. With six mounting options, 10 bore sizes from 12mm to 100mm, strokes up to 300mm, and built-in auto switches, the NCQ2 cylinder can be configured to match your needs. Other options include clean room, copper free, air/oil, built-in fittings, and rubber bumper.

XT581C140-H064-150P

ZCDUKC10-10D-M9BZ