CategoryL3: Chains & Chain Sprockets (Page 1)

Chain Guide, Chain Number 80, Channel Depth 1.19 in, Channel Type Deep Channel, Color Black, For Number of Strands Single, For Pitch Type Single Pitch, Frame Material Stainless Steel, Frame Type Non-Flanged Frame, Guide Material UHMWPE, Maximum Operating Temperature 175 Degrees F, Overall Height 1.58 in, Overall Length 10 ft, Overall Width 1.77 in

DS50ATB16H

Finished BoreBoreRoller Chain Sprocket,26# of Teeth

Finished BoreBoreRoller Chain Sprocket,36# of Teeth

H100B18F 1-7/16 Inch Bore Keyway & 2 Set Screws Fb Hardened Tooth

H40B17F 1-3/16" Inch Bore Keyway & 2 Set Screws Fb Hardened Tooth

H50B23F 1-3/16" Inch Bore Keyway & 2 Set Screws Fb Hardened Tooth

H60B26F 1-7/16" Bore Keyway & 2 Set Screws Fb Hardened Tooth

H80B18F 1-3/16" Bore Keyway & 2 Set Screws Fb Hardened Tooth

Hardened teeth for maximum wear resistance. - Black oxide surface finish to protect against rust. - Precision machined teeth assure maximum transmission efficiency - Keyway on tooth centerline.

Hardened teeth for maximum wear resistance. - Black oxide surface finish to protect against rust. - Precision machined teeth assure maximum transmission efficiency.

QT PowerChain II,8MPC-60S-12-2012

Roller Attachment Link, Attachment Number SA-2, Attachment Type Tab, Material Stainless Steel, Chain Overall Width 0.878 in, Chain Number C2052, Roller Diameter 3/4 in, Finish Plain, Pitch 1 1/4 in, Link Type Roller Attachment, Attachment Location One Side, Centerline to Attachment End 0.969 in, Centerline to Hole Center 0.626 in, Chain Construction Riveted Pin, Extended Pin Diameter Not Applicable, Heavy Series No, Inside Width 3/8 in, Lubrication SAE 10 to SAE 50, Material Grade 600

Roller Attachment Link, Attachment Number SA-2, Attachment Type Tab, Material Stainless Steel, Chain Overall Width 1.225 in, Chain Number C2062H, Roller Diameter 7/8 in, Finish Plain, Pitch 1 1/2 in, Link Type Roller Attachment, Centerline to Attachment End 0.652 in, Centerline to Hole Center 0.573 in, Extended Pin Diameter 0.234 in, Lubrication SAE 10 to SAE 50, Material Grade 600, Maximum Operating Temperature 750 Degrees F, Minimum Operating Temperature -40 Degrees F, Number of Tab Holes 1

SENQCIA 304 stainless steel Mega Chain riveted roller chain is manufactured . They offer excellent resistance against many forms of chemical attack and operate in temperatures ranging from -250 to +750 degrees F. The ultimate strength is nearly the same as carbon steel chains and the working loads are 25%-30% greater than standard stainless steel chains. Packaged chains are supplied with a necessary connecting link to join the ends. This chain is packaged in a 10ft box.

SENQCIA Hi-Max British Standard offset Links are manufactured in accordance with the ISO 606B International roller chain standard. Offset links are supplied with ?flatted? connecting pins and a split cotter for ease of assembly in the field. These special purpose links allow the user to make an endless strand of roller chain from an odd number of pitches. They are also used to reduce the length of a strand by one pitch when normal chain elongation has created excess catenary sag on a roller chain drive. Care however should be taken as the offset link has significantly less load carrying capacity than the base chain itself. Each offset link is individually packaged in a sealed plastic bag.

SENQCIA Hi-Max cottered roller chain is manufactured in accordance with the ASME/ANSI B29.1 American roller chain standard. Packaged chains are pre-lubricated with high quality wax-type grease and come with a necessary connecting link to join the ends. Offset links (used to shorten or lengthen a chain strand by 1 pitch) are also available and sold separately. This chain is packaged in a 10ft box.

SENQCIA Hi-Max cottered type 304 Stainless Steel Double Pitch connecting links are manufactured . They offer excellent resistance against many forms of chemical attack and operate in temperatures ranging from -250 to +750 degrees F. Split cotters are supplied with slip fit closing plates for ease of assembly in the field. Connecting links are used to connect the ends of the roller chain strand into an endless loop. Each connecting link is individually packaged in a sealed plastic bag.

SENQCIA Hi-Max Leaf Chains are manufactured . They are used primarily as tension linkage or force transmision chains for lifts and/or hoists. Assembled chains are wupplied with a rust prevent oil to resist rust durring shipment and storage. This chain is packaged on a 50ft reel.

SENQCIA Hi-Max spring clip type British Standard connecting links are manufactured in accordance with the ISO 606B international roller chain standard. Spring clips are supplied with slip fit closing plates for ease of assembly in the field. Connecting links are used to connect the ends of the roller chain strand into an endless loop. Each connecting link is individually packaged in a sealed plastic bag.

SENQCIA Inspire Series 304 Stainless Steel Double Pitch offset Links are manufactured . They offer excellent resistance against many forms of chemical attack and operate in temperatures ranging from -250 to +750 degrees F. Offset links are supplied with ?flatted? connecting pins and a split cotter for ease of assembly in the field. These special purpose links allow the user to make an endless strand of roller chain from an odd number of pitches. They are also used to reduce the length of a strand by one pitch when normal chain elongation has created excess catenary sag on a roller chain drive. Care however should be taken as the offset link has significantly less load carrying capacity than the base chain itself. Each offset link is individually packaged in a sealed plastic bag.

SENQCIA Inspire Series Perfect Coat Plus II spring clip type connecting links are manufactured in accordance with the ASME/ANSI B29.1 American roller chain standard. They offer exceptional performance and long life in a wide variety applications. The special coating is hexavalent chromium free and provides excellent resistance to corrosive attack in many moderately corrosive applications. Spring clips are supplied with slip fit closing plates for ease of assembly in the field. Closing plates are ?flat? style to improve fatigue strength. Connecting links are used to connect the ends of the roller chain strand into an endless loop. Each connecting link is individually packaged in a sealed plastic bag.

SENQCIA Inspire Series Riv Hollow pin type ANSI/ASME Double Pitch chains with large rollers are manufactured . The hollow pins and bushings are seamless for superior wear resistance. These chains are primarily used on conveyors with through rods inserted into the hollow pins Packaged chains are pre-lubricated with a rust prevent oil and come with a necessary connecting link to join the ends. Offset links (used to shorten or lengthen a chain strand by 1 pitch) are also available and sold separately. This chain is packaged in a 10ft box.

SENQCIA Inspire Series SBR riveted Double Pitch roller chain is manufactured in accordance with the ASME/ANSI B29.4 American roller chain standard. These solid bushing/solid roller chains offer exceptional performance and long life in a wide variety of applications. Nickel plating helps prevent rust in many wet and mildly corrosive environments. Solid cold forged bushings extend chain wear life and greatly reduce break-in wear. Packaged chains are supplied with a necessary connecting link to join the ends. Offset links (used to shorten or lengthen a chain strand by 1 pitch) are also available and sold separately. This chain is packaged in a 10ft box.

SENQCIA Inspire Series spring clip type connecting links are manufactured in accordance with the ASME/ANSI B29.4 American roller chain standard for conveyor series double pitch chains. They offer exceptional performance and long life in a wide variety applications. The same connecting link is used to connect both chains with standard rollers and chains with large rollers. Spring clips are supplied with slip fit closing plates for ease of assembly in the field. Connecting links are used to connect the ends of the conveyor series double pitch chain strand into an endless loop. Each connecting link is individually packaged in a sealed plastic bag.

SENQCIA Ultra-Max 600 series Stainless Steel riveted standard roller Double Pitch chain is manufactured . They offer excellent resistance against many forms of chemical attack and possess percipitation hardened round parts for improved wear performance. Packaged chains are supplied with a necessary connecting link to join the ends. Offset links (used to shorten or lengthen a chain strand by 1 pitch) are also available and sold separately. This chain is packaged in a 10ft box.

SENQCIA Ultra-Max SBR riveted Chrome Plated Pins roller chain is manufactured to a special high performance specification. These solid bushing/solid roller chains offer premium performance and long life in a wide variety of applications. Chrome plating provides an ultra-hard wear surface that performs better in abrasive conditions or applications where lubrication is not possible.Solid cold forged bushings extend chain wear life and greatly reduce break-in wear. Packaged chains are pre-lubricated with high quality wax-type grease and come with a necessary connecting link to join the ends. Offset links (used to shorten or lengthen a chain strand by 1 pitch) are also available and sold separately. This chain is packaged on a 10ft box.

Single Strand Sprocket, Bore Diameter 1 1/4 in, For Chain Pitch 1/2 in, For Number of Strands Single, Hub Type One Side, Material Steel, Maximum Bore Diameter 1 1/4 in, Number of Teeth 23, Outside Diameter 3.94 in, Pitch Diameter 3.672 in, Bore Type Fixed, Chain Number 40, Finish Black Oxide, For Pitch Type Single Pitch, Hub Diameter 3 in, Hub Projection 0.716 in, Includes Set Screws, Keyway Yes, Keyway Depth 1/8 in, Keyway Width 1/4 in, Length through Bore 1 in, Material Grade 1045

Sprocket Chain Rlr P Sgl 1-3/4In 10.46In, 60B42F-1L

Sprocket Chain Rlr P Sgl 1.938In 9-1/2In, 60B38F-1R

Sprocket, For Bushing Size SH, For Bushing Type Quick Detachable, For Chain Pitch 1/2 in, Material Steel, Number of Teeth 22, Outside Diameter 3.78 in, Pitch Diameter 3.513 in, Chain Number 40, For Number of Strands Single, Maximum Bore Diameter 1 5/8 in, Finish Black Oxide, For Pitch Type Single Pitch, Hub Diameter 2 11/16 in, Hub Projection 0.529 in, Hub Type One Side, Length through Bore 13/16 in, Material Grade 1045, Minimum Bore Diameter 1 11/16 in, Resistance Properties Corrosion Resistant

TRITAN Sprocket, 1/2in Pitch, 3/4in Finished Bore, 21 Teeth

Ultra-Max C2080H Cl Cp Type ASME/ANSI Double Pit RllrChn 2" Pit,PK5