This Rexnord ZB2204S standard-duty mounted spherical roller bearing has a 4-bolt round flange block housing and fits a 2-1/4" shaft. The housing is made of cast iron for rigidity and vibration damping and has a powder coating for resistance to corrosion. It is a regreasable, non-expansion type bearing, with a 36,670 lbf dynamic load rating and a 44,400 lbf static load rating. It has precision-ground, superfinished raceways, a 3-5/16" length through the bore, and can accommodate for dynamic and static misalignment up to 2.0 degrees. It has a set screw locking collar for a secure attachment to the shaft and a clearance seal for resistance to contaminants. The flange housing has an outside diameter (OD) of 7-3/4", and it has a pilot extension for accurate placement in the mounting surface bore during installation and increased stability during operation. This mounted bearing has a maximum rotational speed of 3,650 rpm.</p> <p> Rexnord manufactures power transmission components under brands such as Link-Belt, Thomas, and Stearns, and water management products under brands such as VAG and Zurn. The company is headquartered in Milwaukee, WI.</p></div>
This Rexnord ZEP2115 heavy-duty mounted spherical roller bearing has a 2-bolt pillow block housing and fits a 1-15/16" shaft. The housing is made of cast iron for rigidity and vibration damping and has a powder coating for resistance to corrosion. It is a regreasable, non-expansion type bearing, with a 28,890 lbf dynamic load rating and a 33,200 lbf static load rating. It has precision-ground, superfinished raceways, a 3-1/8" length through the bore, and can accommodate for dynamic and static misalignment up to 2.0 degrees. It has a set screw locking collar for a secure attachment to the shaft and a clearance seal for resistance to contaminants. The housing is one-piece, 4-9/16" in height, and has a 2-1/4" base to centerline height. This mounted bearing has a maximum rotational speed of 4,050 rpm.</p> <p> Rexnord manufactures power transmission components under brands such as Link-Belt, Thomas, and Stearns, and water management products under brands such as VAG and Zurn. The company is headquartered in Milwaukee, WI.</p></div>
This Rexnord ZP5203F heavy-duty mounted spherical roller bearing has a 4-bolt pillow block housing and fits a 2-3/16" shaft. The housing is made of cast iron for rigidity and vibration damping and has a powder coating for resistance to corrosion. It is a regreasable, non-expansion type bearing, with a 36,370 lbf dynamic load rating and a 44,400 lbf static load rating. It has precision-ground, superfinished raceways, a 4-1/8" length through the bore, and can accommodate for dynamic and static misalignment up to 2.0 degrees. It has two set screw locking collars for a secure attachment to the shaft and a clearance seal for resistance to contaminants. The housing is one-piece, 5-1/2" in height, and has a 2-3/4" base to centerline height. This mounted bearing has a maximum rotational speed of 3,650 rpm.</p> <p> Rexnord manufactures power transmission components under brands such as Link-Belt, Thomas, and Stearns, and water management products under brands such as VAG and Zurn. The company is headquartered in Milwaukee, WI.</p></div>
This SMC KFH06-02 brass insert tube fitting adapts 1/4" BSPT male thread to 6 mm OD and 4 mm ID tubing. The fitting has British Standard Pipe Taper (BSPT) thread on one end and a compression-type mechanism with a ferrule on the other end. The ferrule provides reliable retaining force on both the inside and outside of the tubing. The brass body resists corrosion, and the connector has a maximum operating pressure of 145 pounds per square inch (psi) and an operating temperature range of -5 to +60 degrees C. This brass insert tube fitting is suitable for use in both vacuum and pressure applications, such as in pneumatic test equipment.Tube fittings are components used for connecting, branching, terminating, and changing the direction of tubing in pneumatic and hydraulic systems. They are made of brass, stainless steel, polybutylene terephthalate (PBT), and other materials that resist corrosion and wear. Tube fittings have various types of connections, including threaded, welded, barbed, and push-to-connect (also called one-touch). Push-to-connect connections do not require tools or sealants. Tube fittings are used in various applications, including machine tools, airplane and truck controls, and automated production lines, among others.SMC Corporation manufactures actuators, valves, airline equipment, connector fittings, electrical products, vacuum products, dryers, temperature control chillers, and accessories. SMC Corporation of America is headquartered in Noblesville, IN, and meets International Organization for Standardization (ISO) standards 9000:2000 and 9001:2008.
This SMC KQ2E bulkhead connector is a brass tube fitting for connecting a tube to a male thread through a panel. It has a push-to-connect inch tube connection on one end and female British Standard Pipe Taper (BSPT) threads on the other end. The fitting is connected to the bulkhead with male Unified Fine (UNF) threads. The body and threads are made of Japanese Industrial Standard (JIS) C3604 brass for corrosion resistance, and the tube seal is made of nitrile butadiene rubber (NBR) for resistance to oils and extreme temperatures. A chuck and collet provide secure retention of tubing, and the release button allows tubing to be removed with little force. The fitting can be used with nylon, soft nylon, polyurethane, fluorinated ethylene propylene (FEP), and perfluoroalkoxy (PFA) tubing. It has an operating pressure range of -14.5 to 145 pounds per square inch (psi) (-100 kPa to 1 MPa), an ambient temperature range of 23 to 140 degrees F (-5 to 60 degrees C), and a fluid temperature range of 32 to 104 degrees F (0 to 40 degrees C). This brass tube fitting is Restriction of Hazardous Substances (RoHS) compliant, and can be used in a broad range of fluid power applications, including temperature control, compressed air equipment, medical instrumentation, and motor vehicle controls, among others.Specifications Connection thread Female BSPT (JIS B0203) Bulkhead mounting thread Male UNF Thread material JIS C3604 brass Compatible tubing materials Nylon, soft nylon, polyurethane, FEP, PFA Fluid Air or water Operating pressure range 14.5 to 145 psi (-100 kPa to 1 MPa) Operating temperature range (ambient) 23 to 140 degrees F (-5 to 60 degrees C) Operating temperature range (fluid)) 32 to 104 degrees F (0 to 40 degrees C)Tube fittings are components used for connecting, branching, terminating, and changing the direction of tubing in pneumatic and hydraulic systems. They are made of brass, stainless steel, polybutylene terephthalate (PBT), and other materials that resist corrosion and wear. Tube fittings have various types of connections, including threaded, welded, barbed, and push-to-connect (also called one-touch). Push-to-connect connections do not require tools or sealants. Tube fittings are used in various applications, including machine tools, airplane and truck controls, and automated production lines, among others.SMC Corporation manufactures actuators, valves, airline equipment, connector fittings, electrical products, vacuum products, dryers, temperature control chillers, and accessories. SMC Corporation of America is headquartered in Noblesville, IN, and meets International Organization for Standardization (ISO) standard 9001:2008.
This SMC KQ2E bulkhead connector is a brass tube fitting for connecting a tube to a male thread through a panel. It has a push-to-connect inch tube connection on one end and female National Pipe Thread Taper (NPT) threads on the other end. The fitting is connected to the bulkhead with male Unified Fine (UNF) threads. The body and threads are made of Japanese Industrial Standard (JIS) C3604 brass for corrosion resistance, and the tube seal is made of nitrile butadiene rubber (NBR) for resistance to oils and extreme temperatures. A chuck and collet provide secure retention of tubing, and the release button allows tubing to be removed with little force. The fitting can be used with nylon, soft nylon, polyurethane, fluorinated ethylene propylene (FEP), and perfluoroalkoxy (PFA) tubing. It has an operating pressure range of -14.5 to 145 pounds per square inch (psi) (-100 kPa to 1 MPa), an ambient temperature range of 23 to 140 degrees F (-5 to 60 degrees C), and a fluid temperature range of 32 to 104 degrees F (0 to 40 degrees C). This brass tube fitting is Restriction of Hazardous Substances (RoHS) compliant, and can be used in a broad range of fluid power applications, including temperature control, compressed air equipment, medical instrumentation, and motor vehicle controls, among others.Specifications Connection thread Female NPT Bulkhead mounting thread Male UNF Thread material JIS C3604 brass Compatible tubing materials Nylon, soft nylon, polyurethane, FEP, PFA Fluid Air or water Operating pressure range 14.5 to 145 psi (-100 kPa to 1 MPa) Operating temperature range (ambient) 23 to 140 degrees F (-5 to 60 degrees C) Operating temperature range (fluid)) 32 to 104 degrees F (0 to 40 degrees C)Tube fittings are components used for connecting, branching, terminating, and changing the direction of tubing in pneumatic and hydraulic systems. They are made of brass, stainless steel, polybutylene terephthalate (PBT), and other materials that resist corrosion and wear. Tube fittings have various types of connections, including threaded, welded, barbed, and push-to-connect (also called one-touch). Push-to-connect connections do not require tools or sealants. Tube fittings are used in various applications, including machine tools, airplane and truck controls, and automated production lines, among others.SMC Corporation manufactures actuators, valves, airline equipment, connector fittings, electrical products, vacuum products, dryers, temperature control chillers, and accessories. SMC Corporation of America is headquartered in Noblesville, IN, and meets International Organization for Standardization (ISO) standard 9001:2008.
This SMC KQ2E bulkhead connector is a brass tube fitting for connecting a tube to a male thread through a panel. It has a push-to-connect metric tube connection on one end and female British Standard Pipe Taper (BSPT) threads on the other end. The fitting is connected to the bulkhead with male metric (M) threads. The body and threads are made of Japanese Industrial Standard (JIS) C3604 brass for corrosion resistance, and the tube seal is made of nitrile butadiene rubber (NBR) for resistance to oils and extreme temperatures. A chuck and collet provide secure retention of tubing, and the release button allows tubing to be removed with little force. The fitting can be used with nylon, soft nylon, polyurethane, fluorinated ethylene propylene (FEP), and perfluoroalkoxy (PFA) tubing. It has an operating pressure range of -14.5 to 145 pounds per square inch (psi) (-100 kPa to 1 MPa), an ambient temperature range of 23 to 140 degrees F (-5 to 60 degrees C), and a fluid temperature range of 32 to 104 degrees F (0 to 40 degrees C). This brass tube fitting is Restriction of Hazardous Substances (RoHS) compliant, and can be used in a broad range of fluid power applications, including temperature control, compressed air equipment, medical instrumentation, and motor vehicle controls, among others.Specifications Connection thread Female BSPT (JIS B0203) Bulkhead mounting thread Male metric (M) Thread material JIS C3604 brass Compatible tubing materials Nylon, soft nylon, polyurethane, FEP, PFA Fluid Air or water Operating pressure range 14.5 to 145 psi (-100 kPa to 1 MPa) Operating temperature range (ambient) 23 to 140 degrees F (-5 to 60 degrees C) Operating temperature range (fluid)) 32 to 104 degrees F (0 to 40 degrees C)Tube fittings are components used for connecting, branching, terminating, and changing the direction of tubing in pneumatic and hydraulic systems. They are made of brass, stainless steel, polybutylene terephthalate (PBT), and other materials that resist corrosion and wear. Tube fittings have various types of connections, including threaded, welded, barbed, and push-to-connect (also called one-touch). Push-to-connect connections do not require tools or sealants. Tube fittings are used in various applications, including machine tools, airplane and truck controls, and automated production lines, among others.SMC Corporation manufactures actuators, valves, airline equipment, connector fittings, electrical products, vacuum products, dryers, temperature control chillers, and accessories. SMC Corporation of America is headquartered in Noblesville, IN, and meets International Organization for Standardization (ISO) standard 9001:2008.
This SMC KQ2F female adapter (also called connector) is a brass tube fitting for connecting a tube to a male thread. It has a push-to-connect metric tube connection on one end and female British Standard Pipe Taper (BSPT) threads on the other end. The body and threads are made of Japanese Industrial Standard (JIS) C3604 brass for corrosion resistance, and the tube seal is made of nitrile butadiene rubber (NBR) for resistance to oils and extreme temperatures. A chuck and collet provide secure retention of tubing, and the release button allows tubing to be removed with little force. The fitting can be used with nylon, soft nylon, polyurethane, fluorinated ethylene propylene (FEP), and perfluoroalkoxy (PFA) tubing. It has an operating pressure range of -14.5 to 145 pounds per square inch (psi) (-100 kPa to 1 MPa), an ambient temperature range of 23 to 140 degrees F (-5 to 60 degrees C), and a fluid temperature range of 32 to 104 degrees F (0 to 40 degrees C). This brass tube fitting is Restriction of Hazardous Substances (RoHS) compliant, and can be used in a broad range of fluid power applications, including temperature control, compressed air equipment, medical instrumentation, and motor vehicle controls, among others.Specifications Connection thread Female BSPT (JIS B0203) Thread material JIS C3604 brass Compatible tubing materials Nylon, soft nylon, polyurethane, FEP, PFA Fluid Air or water Operating pressure range 14.5 to 145 psi (-100 kPa to 1 MPa) Operating temperature range (ambient) 23 to 140 degrees F (-5 to 60 degrees C) Operating temperature range (fluid)) 32 to 104 degrees F (0 to 40 degrees C)Tube fittings are components used for connecting, branching, terminating, and changing the direction of tubing in pneumatic and hydraulic systems. They are made of brass, stainless steel, polybutylene terephthalate (PBT), and other materials that resist corrosion and wear. Tube fittings have various types of connections, including threaded, welded, barbed, and push-to-connect (also called one-touch). Push-to-connect connections do not require tools or sealants. Tube fittings are used in various applications, including machine tools, airplane and truck controls, and automated production lines, among others.SMC Corporation manufactures actuators, valves, airline equipment, connector fittings, electrical products, vacuum products, dryers, temperature control chillers, and accessories. SMC Corporation of America is headquartered in Noblesville, IN, and meets International Organization for Standardization (ISO) standard 9001:2008.
This SMC KQ2P-23 plug tube fitting has a 3.2 mm OD and 31.5 mm length, and is intended for use in terminating SMC KQ2 series push-to-connect fittings. The white color polybutylene terephthalate (PBT) fitting resists corrosion and has an operating temperature range of -5 to +60 degrees C. It has a maximum operating pressure of 145 pounds per square inch (psi) and a maximum operating vacuum of -100 kilopascals (kPa). This KQ2 series plug tube fitting is suitable for use with air and water in both vacuum and pressure applications, such as in food processing.Tube fittings are components used for connecting, branching, terminating, and changing the direction of tubing in pneumatic and hydraulic systems. They are made of brass, stainless steel, polybutylene terephthalate (PBT), and other materials that resist corrosion and wear. Tube fittings have various types of connections, including threaded, welded, barbed, and push-to-connect (also called one-touch). Push-to-connect connections do not require tools or sealants. Tube fittings are used in various applications, including machine tools, airplane and truck controls, and automated production lines, among others.SMC Corporation manufactures actuators, valves, airline equipment, connector fittings, electrical products, vacuum products, dryers, temperature control chillers, and accessories. SMC Corporation of America is headquartered in Noblesville, IN, and meets International Organization for Standardization (ISO) standards 9000:2000 and 9001:2008.
This SMC KQ2T reducing tee is a PBT tube fitting for connecting two tubes at 90-degree angles to a third tube of a larger size. It has push-to-connect inch tube connections on all three ends. The body is made of polybutylene terephthalate (PBT) for corrosion resistance, and the tube seals are made of nitrile butadiene rubber (NBR) for resistance to oils and extreme temperatures. A chuck and collet provide secure retention of tubing, and the release button allows tubing to be removed with little force. The fitting can be used with nylon, soft nylon, polyurethane, fluorinated ethylene propylene (FEP), and perfluoroalkoxy (PFA) tubing. It has an operating pressure range of -14.5 to 145 pounds per square inch (psi) (-100 kPa to 1 MPa), an ambient temperature range of 23 to 140 degrees F (-5 to 60 degrees C), and a fluid temperature range of 32 to 104 degrees F (0 to 40 degrees C). This PBT tube fitting is Restriction of Hazardous Substances (RoHS) compliant, and can be used in a broad range of fluid power applications, including temperature control, compressed air equipment, medical instrumentation, and motor vehicle controls, among others.Specifications Compatible tubing materials Nylon, soft nylon, polyurethane, FEP, PFA Fluid Air or water Operating pressure range 14.5 to 145 psi (-100 kPa to 1 MPa) Operating temperature range (ambient) 23 to 140 degrees F (-5 to 60 degrees C) Operating temperature range (fluid)) 32 to 104 degrees F (0 to 40 degrees C)Tube fittings are components used for connecting, branching, terminating, and changing the direction of tubing in pneumatic and hydraulic systems. They are made of brass, stainless steel, polybutylene terephthalate (PBT), and other materials that resist corrosion and wear. Tube fittings have various types of connections, including threaded, welded, barbed, and push-to-connect (also called one-touch). Push-to-connect connections do not require tools or sealants. Tube fittings are used in various applications, including machine tools, airplane and truck controls, and automated production lines, among others.SMC Corporation manufactures actuators, valves, airline equipment, connector fittings, electrical products, vacuum products, dryers, temperature control chillers, and accessories. SMC Corporation of America is headquartered in Noblesville, IN, and meets International Organization for Standardization (ISO) standard 9001:2008.