Label: ['Onsrud']

Products with this attribute (49 total)

1" Two Flute Routing End Mill Corner Radius 5"L

1" Two Flute Routing End Mill Square, 3-1/8" Neck

1/2" Three Flute Routing End Mill Ball Nose 4"L

1/4" Three Flute Routing End Mill Ball Nose 2"L

5/8" Three Flute Routing End Mill Ball Nose 4"L

5/8" Three Flute Routing End Mill Square 3"L

5/8" Two Flute Routing End Mill Square, 3-1/8" Neck

Ball End Mill, 3/8 in Milling Dia., Carbide, Bright (Uncoated), Non-Coolant Through

Corner Radius End Mill, 1 in Milling Dia., Carbide, Bright (Uncoated), Straight, Fractional Inch, 1/4 in, 1 1/4 in, 4 in

Corner Radius End Mill, 1 in Milling Dia., Carbide, Bright (Uncoated), Straight, Fractional Inch, 1/4 in, 2 1/2 in, 5 in

Corner Radius End Mill, 1 in Milling Dia., Carbide, TiN, Straight, Fractional Inch, 0.03 in, 1 1/4 in, 5 in

Corner Radius End Mill, 1/4 in Milling Dia., Carbide, Bright (Uncoated), Straight, Fractional Inch, 0.015 in, 3/8 in, 2 in

Corner Radius End Mill, 3/8 in Milling Dia., Carbide, Bright (Uncoated), Straight, Fractional Inch, 0.015 in, 1/2 in, 5 in

Corner Radius End Mill, 3/8 in Milling Dia., Carbide, TiN, Straight, Fractional Inch, 0.09 in, 1/2 in, 4 in

Corner Radius End Mill, 3/8 in Milling Dia., Carbide, TiN, Straight, Fractional Inch, 0.12 in, 1/2 in, 4 in

Corner Radius End Mill, 5/8 in Milling Dia., Carbide, Bright (Uncoated), Straight, Fractional Inch, 0.03 in, 3/4 in, 4 in

Onsrud 83-310AlTiN | Routing End Mill Up Spiral 3/16 3/8 | 4KPH7 | Raptor Supplies Worldwide

Onsrud Cor Rad End Mill,1",Carb,0.0300" rad AMC707260 ZO-G5670122 - SIM Supply

Onsrud Cor Rad End Mill,3-8",Carb,0.0150" rad AMC700856 ZO-G5707983 - SIM Supply

Onsrud Cutter AMC716284 1" x 1.25" Medium Length Necked Router Bit | burnstools.com

Square End Mill, 1/4 in Milling Dia., Carbide, Bright (Uncoated), Straight, Length of Cut 3/8 in, Overall Length 4 in, Shank Dia. 1/4 in, Neck Dia. 15/64 in

Square End Mill, 1/4 in Milling Dia., Carbide, Bright (Uncoated), Straight, Length of Cut 3/8 in, Overall Length 4 in, Shank Dia. 1/4 in, Neck Dia. 15/64 in

Square End Mill, 3/8 in Milling Dia., Carbide, Bright (Uncoated), Straight, Length of Cut 1 1/2 in, Overall Length 4 in, Shank Dia. 3/8 in, Neck Dia. Not Applicable

Square End Mill, 3/8 in Milling Dia., Carbide, Bright (Uncoated), Straight, Length of Cut 1/2 in, Overall Length 4 in, Shank Dia. 3/8 in, Neck Dia. 11/32 in