PrimarySeller: Quality Tool Warehouse

Products with this attribute (94 total)

Agricultural Fan Motor Split-Phase 1 HP Nameplate RPM 1725 Voltage 115/230 1 Phase Frame 56 Totally Enclosed Air-Over Full Load Amps 13.0/6.5 60 Hz Rigid Base Motor Mounting Type Motor Thermal Protection Auto Ins. Class B Motor Service Factor 1.25 Ball Motor Bearings Max Ambient Temperature 40 Degrees C CW/CCW Motor Shaft Rotation Overall Length 11-5/8 In. Shaft Dia 5/8 In. Shaft Length 1-7/8 In. Motor Frame Material Rolled Steel Includes Slinger

Aluminum Heat Reflector In.U In. For Use With No 3F835 U-Bend Fitting

ARDUPG1927195L12B

ARDUPG3102215L12A

ARDUPG3110396L12A

ARDUPG3471641L12C

ARDUPG4798254L12C

Backdraft Damper / Wall Shutter Fits Fan Dia 12 In. Shutter Overall Size 15 in x 15 In. Shutter Construction Material Fiberglass Frame and Stainless Steel Tie Rod Shutter Opening Required 12-1/2 in x 12-1/2 In. Shutter Free Area 0.786 sq. ft. Vertical Shutter Mounting Position Shutter Mounting Location Wall Frame Depth 3 In. Open Depth 6-1/4 In. Flange Width 1-1/2 In. Mounting Hole Size Prepunched Max Velocity 2500 FPM Blade Material Beige Fiberglass

Backdraft Damper Roof Mount Exhaust Damper Size 23 x 23 In Overall Size 25 x 25 In Flange Width 1 In Max Velocity 2250 FPM Construction Material G-90 Galvanized Steel Frame Aluminum Blades Stainless Steel Pivot Pins Nylon Bushings and Galvanized Steel Tie Rods. Includes Pre-punched Conduit Hole Knock-out and Felted Edges For Quiet Operation

Control Transformer VA Rating 150VA Input Voltage 208/240/277/380/480VAC Output Voltage 24VAC 80 Degrees C Temp Rise Fused Yes 50/60 Hz Transformer Type Encapsulated 1 Phase Mounting Panel Enclosure Finish Epoxy Resin Varnish Height 5.27 In. Depth 4.00 In. Width 3.75 In. Standards UL 506 Listed cUL Listed CSA Approved NEMA ANSI Requirements CE Marking Includes 2-Pole Class In.CC in Fuse Block Manufacturers Warranty Length 3 yr.

Ergodyne 19301 Squids 3001 Retractable Single Carabiner w Loop End - 2lbs, Black

Fan Guard For Tubeaxial Fan Dia 18 In. For Use with Fans 4TM82 and 4C661 Depth 3/16 In. Finish Baked On Gray Polyester

General Purpose Motor 3-Phase Totally Enclosed Fan-Cooled 2 HP Nameplate RPM 3500 143/5TC Frame Voltage 230/460 60 Hz 3 Phase 5.1/2.5 Full Load Amps No of Speeds 1 Motor Mounting Type Face Motor Mounting Position Horizontal Motor Thermal Protection None Ins. Class F 1.15 Motor Service Factor Ball Motor Bearings Motor Frame Material Rolled Steel Max Ambient Temp 40 Degrees C CW/CCW Motor Shaft Rotation Overall Length 13-5/8 In. Motor Shaft Design KeyedWARNING: California ResidentsThis product can expose you to chemicals including Styrene, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

Guard Inlet Height (In.) - Width (In.) - Depth (In.) 1 Outside Dia (In.) 6 Agency Compliance OSHA Compliant Construction Material Steel Finish Gray Baked on Polyester Epoxy Powder Coat Application Provides Protection on Inlet of Blower For Use With 4C108 and 4C129 Includes Mounting Hardware

Johnson Box Level, Aluminum, 24in L, Yllw, 4 Magnets

Motor Mounting Bracket Double Wire Steel 5 In Diameter For Use with NEMA 42 Frame Motors Provides Lug-Style Mounting to Facilitate Using Motor in Blower Applications Includes 3 Lugs 1 Bolt 1 Nut

Pipe Cutter Wheel, 1/8-2 In

Putty Knife, Flexible, 1-1/2", Carbon Steel This product contains a chemical that is regulated under California Proposition 65. Warning: This product contains a chemical known to the State of California to cause cancer. Warning: This product contains a chemical known to the State of California to cause birth defects or other reproductive harm. -

Washdown Motor 3-Phase 1/2 HP 3550 Nameplate RPM Voltage 230/460 Phase 3 56C Frame Totally Enclosed Nonventilated Full Load Amps 1.4/0.7 60 Hz All Angle Motor Mounting Position Motor Thermal Protection None F Ins. Class Motor Service Factor 1.15 Ball Motor Bearings Max Ambient Temp 40 Degrees C CW/CCW Motor Shaft Rotation Overall Length 10-9/16 In. Shaft Dia 5/8 In. Shaft Length 2 In. Length Less Shaft 9-11/16 In. Continuous Duty

WESTWARD 10T712 Round Adjustable Die Material High Speed Steel Thread Direction Right Hand Size 3 Pitch 48 Thread Type NC Outside Dia. 13/16 In Thickness 1/4 In Application Used For Hand Threading

WESTWARD 2RUL9 Screw Extractor Spiral Flute For Removing Studs Bolts Screws 1/4 to 5/16 Size #2 Drill Size (In.) 7/64 Overall Length (In.) 2-3/8 Taper Length (In.) 3/4 Small End Dia. (In.) 1/12 Large End Dia. (In.) 3/16 Carbon Steel Removing Broken Screws Bolts and Other Threaded Parts

WESTWARD 5PLP6 Jobber Drill Standard Number of Pieces 1 General Purpose Grade High Speed Steel Black Oxide Finish Conventional Point Drill Point (Deg.) 118 Metric Size 5.00 Decimal Equivalent 0.1969 Flute Length (In.) 2-3/64 Flute Length (mm) 52 Overall Length (In.) 3-3/8 Overall Length (mm) 86 For Drilling Holes into Carbon Steel Plastic and Cast Iron Materials

WESTWARD 6PRX0 Parabolic Jobber Drill Bit Parabolic Number of Pieces 1 High Speed Steel TiN Finish Split point Drill Point (Deg.) 135 Letter Size U Decimal Equivalent 0.3680 Flute Length (In.) 3-3/16 Overall Length (In.) 5 Shank Dia. (In.) 0.3680 Shank Dia. (mm) 9.3472 Tool Steels Carbon Steel Plastic Cast Iron

WESTWARD 6PRY1 Parabolic Jobber Drill Bit Parabolic Number of Pieces 1 High Speed Steel TiN Finish Split point Drill Point (Deg.) 135 Metric Size 4 Decimal Equivalent 0.1575 Flute Length (In.) 1-11/16 Flute Length (mm) 43 Overall Length (In.) 3 Overall Length (mm) 75 Shank Dia. (In.) 0.1575 Tool Steels Carbon Steel Plastic Cast Iron