Brand: Chemglass Products

All products from this brand (58 total)

A 1: 5 taper PTFE plug having a threaded needle Valve to allow the adjustment of flow through the bore of the plug.
Abbreviate Message Split</p>");
Adapter permits vessels to be purged with an inert gas during sampling or transfer with a af-0519 cannula. Available with a choice of a 4mm high vacuum glass Stopcock having a s.S. Constant pressure retention device or a 4mm PTFE Stopcock. Both the glass and PTFE Stopcock have 9mm OD medium wall arms for use with cg-3022-05 red or cg-3022-22 white septum stopper. Additional arm is provided for connection to inert gas source. Supplied with two cg-3022-05 red septum stopper.
Agitators are made entirely of PTFE and glass filled PTFE and are for use with 30mm OD stirrer shaft cg-2097 in 75 and 100L reactors. The 45? angle impellers are set up to stir downwards in a clockwise direction and upwards when rotated counter-clockwise. The upper agitator hub is open so that it can be positioned wherever the indents are along the 30mm shaft. Locks onto shaft with a collet hub and nut and has a glass filled PTFE safety screw. Heavy-duty blades are 6.5mm thick.
B01EYSSBIQ
B01N5LTCH6
Blanks for fabrication of single or multi-neck round bottom flasks., 20000Ml capacity, Round bottom glassblower flask, For fabrication of single or multi-neck round bottom flasks
Brown, low compression, 75 durometer Viton O-rings are suitable for acids, aliphatic hydrocarbons, oxidizing agents, and all petroleum products Note: Viton O-ring They are especially good for vacuum service and low gas permeability. Temperature range: 30 to 200C (22 to 392F).
Caps. GL Thread Size: ; Aperture Size: .mm. All fluoropolymer resin end fittings are designed with a series of bellows that expand under pressure to seal against the internal wall of the GL thread.
CG-1860-14
Chemglass 5-port L vacuum manifold; Vacuum Manifold, Left Handed, 5 Ports, 0-4mm Chem-Cap Valve, 360mm Overall width
Chemglass Adapter, Gas Inlet, 24/40, Ho; Adapter, Gas Inlet, 24/40, Hose Connection, Long Stem
Chemglass Baffle Assembly, 24/40. 410mm; PTFE Baff
Chemglass Cap, GL-32, Blue, Vented,; Cap, GL-32, Blue, Vented, Non-Sterile, Polypropylene, Pack of 5
Chemglass Connections, Hose, 4 Ring; Connections, Hose, Glass Blowers, 4 Ring, Serrations are tooled on both ends of an 8" length of tubing
Chemglass Cuvette, PMMA, Semi-Micro; Cuvette, PMMA, Semi-Micro
Chemglass Flask, Round Bottom, 1000mL,; Flask, Round Bottom, 1000mL, Heavy Wall, 45/50- 29/42, 4-Neck, Vertical
Chemglass Flask, Round Bottom, 100mL,; Flask, Round Bottom, 100mL, 14/20, Heavy Wall, with #7 Chem-Thread
Chemglass Flask, Round Bottom, 12000mL,; Flask, Round Bottom, 12000mL, Heavy Wall, 45/50 - 24/40, 4-Neck, Vertical
Chemglass Flask, Round Bottom, 25mL,; Flask, Round Bottom, 25mL, Heavy Wall, 14/20 -14/20, 4-Neck, Angled 20??
Chemglass Flask, Volumetric, 500mL, PP,; Flask, Volumetric, 500mL, PolyPro, Class B, GL-25, Tolerance: ??0.50mL
Chemglass Flask, Volumetric, PMP, 25mL,; Flask, Volumetric, 25mL, Polymethylpentene, Class A, 10/19, Tolerance: ??0.04mL
Chemglass Pipetters, Multichannel,; Pipetters, Multichannel, 8-Channel, Variable Volume, 2-20??L, Grey, Each
Chemglass Reaction Vial, 20mL, Complete,; Reaction Vial, 20mL, Complete,Clear, 28 x 57 mm, with 24-400, Green Open Top Cap, TFE Septa,100/Pkg
Chemglass Single Channel Variable Pipett; Single Channel Variable Pipettor, 20-200??L, MicroPette??
Chemglass Temperature Controller,; Temperature Controller, Model 270, Complete, Type J
Chemglass Vessel, Peptide, 10mL,; Vessel, Peptide, 10mL, Medium Porosity, 2-PTFE Stopcocks
Chemglass Vessel, Peptide, 250mL,; Vessel, Peptide, 250mL, Medium Porosity, PTFE T-Bore, Stopcock
Chemglass Vial, Micro Product, 3mL,; Vial, Micro Product, 2mL, GPI 20-400
Chemglass VORTEX MIXER,; Vortex Mixer I/R Kit, Low Profile, 100-240v, U.S. Plug
Clamp 2-Prong Dual
Coiled extension cords to connect thermocouples to instrumentation such as temperature monitors, controllers and data loggers. Cords are 10ft long and made of 26-guage multistrand wire with PVC insulation. All cords have a female standard (OST) with a choice of a male standard (OST) or mini (SMP) connection
Designed for use in temperature controlled chemical and biological reactions. Bottom interior surface is conical in shape to help eliminate spinout when used with CG-2005 egg shaped spinbars. Hose connections have an O.D. of 10mm at the largest serration.
ECO FUNNELS PLASTIC WASTE CONTAINERS Plastic waste container for ECO Funnels
Edges on all sizes are ground and chamfered
European style flask with tapered walls and a Shallow hemispherical bottom for more efficient mechanical or magnetic stirring. Entire body of the flask is jacketed and has two hose connections for circulation of heating or cooling liquid. With standard taper outer joints on center and side necks. Flasks are available with joint configurations other than those listed.
Evaporating flask for use with rotary evaporators. Flasks have a heavy wall for vacuum applications and are balanced to prevent run-out during rotation.
Flasks are designed for culturing organisms that require a large surface area to volume ratio. Available with a plain 59mm ID neck, 38mm OD Delong style neck or GL-45 screw neck with a solid or vented cap.
Flat bottom borosilicate flask for use with Labconco and Virtis freeze dryers. Wide mouth design provides easy access sample.
Flat bottom spinner flasks promote optimal growth of suspension cultures. The complete system includes a flask with two angled sidearms and a PTFE Paddle with glass shaft that adjusts through the compression fitting in the cap.
Flow control adapter for use with cg-1192 and cg-1193 chromatography columns along with cg-1194 reservoirs. Adapter has a 0-4mm chem-cap metering plug.
Funnel has a sealed-in glass fritted disc of the listed porosity. Useful wherever filter paper or membranes cannot withstand the chemical attack of the filtrate. Constructed with heavy wall stems and the top of the funnel is beaded for additional strength.
General purpose single bank vacuum manifold with 3, 4, or 5 ports. Main tube is 38mm OD with a serrated hose connection, having the smallest serration 13.5mm and the largest serration 15.5mm, located at either the left or right side for vacuum connection. Ports are either 0-4mm or 0-8mm chem-vac chem-cap valves with serrated hose connections. The 0-4mm has the smallest serration 10mm and the largest serration 11mm, while the 0-8mm has the smallest serration 13.5mm and the largest serration 15.5mm. Ports are spaced 60mm center to center for the 0-4mm and 75mm center to center for the 0-8mm size.
General purpose, double-bank manifold for use with vacuum and inert gas. Both banks are made from ??" medium wall tubing with 10mm (0.39") O.D. serrated connections. Stopcocks are glass 4mm (0.16") bore with lower vacuum chamber and are spaced 85mm (3.35") center to center. Manifold has top right connection to inert gas and lower left connection for vacuum.
High recovery vial with a conical bottom for complete sample recovery. -Boxes are marked with alpha-numeric coordinates for fast and easy vial identification -Available complete with open-top caps or vials only These vials are the same size or slightly smaller on the OD to allow them to be interchanged with any racks or blocks that accept standard dram or scintillation vials. Packed in an SBS coated white tray complete with SBS partition.
New ChemRxnHub process systems are complete with benchtop stand, overhead stirrer and glassware. Available with the optional manifold connection and heat transfer fluid draining system. The unique design of the ChemRxnHub support stand and clamping system allows for quick and easy installation/removal of glassware and fits into most benchtop hoods. Click the link below for complete system components.
Non-calibrated tubes made from borosilicate glass for use with aqueous and organic solutions. Packed in half pound packages.
Outer joint having a tubulation sealed at the midpoint of the ground portion, and a corresponding hole drilled in the inner joint permitting venting of the side tube when the inner joint is turned to the proper position. Both of the 19/38 sizes are compatible with Buchi Rotary Evaporators. Part number CG-132-02 has a single sidearm and a drip tip permitting the seal to be made for the PTFE feed tube. Part number CG-132-03 has two side arms sealed 180? apart and is used for replacement on the vertical cold trap condenser assembly.
Round bottom, HEAVY WALL, five-neck flask with standard taper outer joints on the center neck and vertical side necks.
Similar to CG-1016, but made entirely of PTFE. Made in United States of America. Easy to Use and Reliable.
Similar to CG-975 CHEM-VAC valve but with the arms bent to minimize hold up of fluids. Valve has a glass plug with three O-rings, the tip O-ring making the primary seal on the precision formed tapered seat. Available with a choice of Viton, Ethylene Propylene (E.P.) or Kalrez O-rings. See CG-983 for replacement plug and CG-585 for O-ring replacement kit. If individual O-ring is required see CG-305 for Viton, CG-303 for Ethylene Propylene (E.P.) or CG-308 for Kalrez. For replacement glass portion of valve only see CG-905.
Single neck, flat bottom flask with a standard taper outer joint. Made in United States of America. Easy to Use and Reliable.
Solid aluminum metal chamber for 96 well PCR plate or tubes. Ideal way to keep PCR tubes and plates cold during sample preparation. Place the metal chamber in an ice bucket or on Lab Armor Beads
Solid Bushing for use with cg-360 internal glass threads. Supplied with one Viton O-Ring., Size #50, Ptfe, 229 viton o-ring
Steam sterilization is convenient and affordable with the new BioClave?? digital research autoclaves. -It includes a mechanical and electrical safety interlock -It prevents the door from being opened until the pressure has reached zero psi -With a width of less than 18 inches it will fit comfortably on even the most crowded bench tops. -Three trays are supplied with each unit along with a convenient tray removal tool The sterilization chambers are large, accommodating a variety of liquids, media, instruments, glassware, plastic ware and other common laboratory items. With large digital displays and fully automatic operation, all segments of the sterilization cycle (fill, sterilize, exhaust and dry) commence and run to completion by simply pressing the start button.The 16 liter BioClave?? offers three cycle options (standard programs), which are preset for the sterilization of liquids, wrapped instruments or unwrapped instruments/plastic ware. A fourth option, ??Dry Only?, is also available for additional drying tie to be added to the end of a cycle. For special applications requiring variations in cycle parameters, all settings on the 16 liter BioClave?? are fully adjustable. CE approved.
The support jack is resistant to sanitizing agents and autoclavable for sterile applications Provides long life, especially when stored and used in corrosive environments Can be used to support flasks, jars, columns, large baths, magnetic stirrers, heaters etc. Support jack deck is constructed of either stainless steel or anodized aluminum, while the lift mechanism for both is constructed entirely from type 304 stainless steel and PTFE.
Vessel has four vertical gland-45 threaded side necks and a 100mm threaded center neck. The 3 and 6 liter vessels are low profile to maximize incubator space. Supplied complete with (4) solid gland-45 caps and (4) pouring Rings.
Wide mouth design facilitates mixing, pipette access, sampling and filling. Unique Flat Bottom Interior permits the use of a standard stir bar. Large permanent white letters make the capacity clearly visible. Flasks are calibrated "To Contain" at Class A tolerances, per ASTM E288 specifications. Supplied complete with either a [ST] glass pennyhead or PTFE stopper.