Turbine Pump, Type Bronze-Fitted, HP 3/4, Phase 1, Voltage 115/230, Inlet (In.) 1-1/4, Outlet (In.) 1, Motor Enclosure ODP, NEMA/IEC Frame 56C, Motor Type Cap-Start, ODP, Wetted Materials Cast Iron, Bronze Fitted, Impeller Material Bronze, Housing Material Cast Iron, Volute Material Cast-Iron, Bronze Fitted, Screw Material Steel, Seal Type Type 21, Seal Material Carbon, Ceramic, Buna, Seal Application Low Flow, High Head, Max. Liquid Temp. (F) -20 to 230, GPM @ 10 PSI 7.5, GPM @ 20 PSI 7.3, GPM @ 30 PSI 7.0, GPM @ 50 PSI 6.8, GPM @ 60 PSI 6.6, GPM @ 75 PSI 6.3, GPM @ 100 PSI 6.0, Max. Pressure (PSI) 300, Best Efficiency GPM @ Head (Ft.) 6.0 GPM @ 100, Best Efficiency Range GPM @ Head (Ft.) 6.0-7.0@ 100-35 PSI, Max. Specific Gravity 1.00 SP, Max. Case Pressure (PSI) 300, Max. Fluid Viscosity 250 SSU, Inlet Pressure (PSI) 200, Impeller Type Regenerative Turbine, Bearing Type Sealed Ball Bearing (Motor Bearing), Duty Continuous, Max. Dia. Solids (In.) 25 Microns, Port Rotation 90 IncremenWARNING: California ResidentsThis product can expose you to chemicals including Styrene, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
Unit Bearing Motor, Motor Application HVAC/R, Motor Sub Application Refrigerator/Freezer, Motor Type Shaded Pole, Enclosure Totally Enclosed Air-Over, HP 1/185, Nameplate RPM 1550, Frame Nonstandard, Voltage 115, Hz 60/50, Phase 1, Full Load Amps 0.34, Output Watts 4, Mounting Rear and Foot, Thermal Protection Impedance, Insulation Class A, Service Factor 1.0, Bearings Sleeve, Frame Material Aluminum, Max. Ambient Temp. 40 Degrees C, Rotation CCWLE, Length Less Shaft 3-3/8", Overall Length 3-7/8", Shaft Type Threaded 1/4-20, Shaft Dia. 1/4", Shaft Length 1/2", Shaft Orientation Up, Down or Horizontal, Body Dia. 3-1/2", Bolt Circle Dia. 2-13/16", RPM Range 1501-1600WARNING: California ResidentsThis product can expose you to chemicals including Styrene, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
Washdown Motor, Motor Application Washdown, Motor Type 3-Phase, Enclosure Totally Enclosed Fan-Cooled, HP 1, Nameplate RPM 1165, Frame 145TC, NEMA Design B, Rotation CW/CCW, Voltage 208-230/460, Full Load Amps 4.2-4.0/2.0, Phase 3, Hz 60/50, Mounting Face/Base, Bearings Ball, Frame Material Stainless Steel, Thermal Protection None, Service Factor 1.15, Max. Ambient Temp. 40 Degrees C, Shaft Dia. 7/8", Shaft Length 2-1/4", Body Dia. 6-15/32", Length Less Shaft 10-3/8", Overall Length 12-9/16", Insulation Class F, RPM Range 1101-1200, Duty Continuous, Shaft Material 300 Series Stainless Steel, Conduit Box Split Clam Shell with Rubber Gasket, Drain Plugs 4 Condensate Drains (at 3, 6, 9 and 12 O'clock) in Both Endshields Plus 2 T-Drains (1 Pre-Installed Opposite Shaft End at 6 O'clock, the Other Loose in the Carton for Customer Installation at Lowest Point of Motor), Endshields 300 Series Stainless Steel, Nominal Efficiency 82.5%, Includes Shaft Key, Protective Shaft Sleeve and 2 StainlessWARNING: California ResidentsThis product can expose you to chemicals including Styrene, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.