Brand: ['Mystery Electronics']

Products with this attribute (8 total)

Import pre-configured templates into your DSP configuration / design software and have your <strong>EasyMix EM12</strong> running in minutes, or build your interface from scratch for a fully customized solution. Equipped with six physical motorized fader channels, two programmable backlit push buttons and two status indicating LED?s per channel located above each fader. Additional programmable bank selection push buttons and status LED?s provide up to 24 programmable virtual fader channel positions. Faders can also be programmed to function as high and low frequency EQ controls. Each fader channel comes equipped with 1 Full 100 mm motorized fader, 2 Programmable back-lit push buttons and 2 Status indicating LED?s.</p><p>Each channel?s push buttons are programmed to provide Auto Mixer on / off and Channel on / off control. Channel LED?s are programmed to indicate status of Auto Mixer highest gain and Signal presence. The Fader buttons are pre-programmed to allow bank selection of faders 1 - 6 or 7 - 12. The EQ buttons are pre-programmed for High gain level and Low gain level control of a DSP Equalization Filter. All program choices can be fully customized to your application requirements. The power indicator LED can also be modified via internal jumper to accept 5, 12 & 24 VDC.</p><p>Eight user defined back-lit push buttons switches are available to control system selection or can be used to trigger presets. Power switch can also be used to trigger an external power sequencer, with the status LED then controlled by the power sequencer, to allow single push button control of the sound system. Power connections can be field modified via internal jumper to allow the EM12 power to be controlled remotely. The EM12 ships with a powder coated steel faceplate and customizable text and graphics using a printed vinyl and a durable plastic overlaminate. All electronics are rear mounted in a 16 gauge enclosure that has been certified to comply with Part 15 of the FCC Rules.</p>
Import pre-configured templates into your DSP configuration / design software and have your <strong>EasyMix EM12</strong> running in minutes, or build your interface from scratch for a fully customized solution. Equipped with six physical motorized fader channels, two programmable backlit push buttons and two status indicating LED?s per channel located above each fader. Additional programmable bank selection push buttons and status LED?s provide up to 24 programmable virtual fader channel positions. Faders can also be programmed to function as high and low frequency EQ controls. Each fader channel comes equipped with 1 Full 100 mm motorized fader, 2 Programmable back-lit push buttons and 2 Status indicating LED?s.</p><p>Each channel?s push buttons are programmed to provide Auto Mixer on / off and Channel on / off control. Channel LED?s are programmed to indicate status of Auto Mixer highest gain and Signal presence. The Fader buttons are pre-programmed to allow bank selection of faders 1 - 6 or 7 - 12. The EQ buttons are pre-programmed for High gain level and Low gain level control of a DSP Equalization Filter. All program choices can be fully customized to your application requirements. The power indicator LED can also be modified via internal jumper to accept 5, 12 & 24 VDC.</p><p>Eight user defined back-lit push buttons switches are available to control system selection or can be used to trigger presets. Power switch can also be used to trigger an external power sequencer, with the status LED then controlled by the power sequencer, to allow single push button control of the sound system. Power connections can be field modified via internal jumper to allow the EM12 power to be controlled remotely. The EM12 ships with a powder coated steel faceplate and customizable text and graphics using a printed vinyl and a durable plastic overlaminate. All electronics are rear mounted in a 16 gauge enclosure that has been certified to comply with Part 15 of the FCC Rules.</p>
Mystery Electronics backboxes are UL Listed and conform to all applicable N.E.M.A. Standards. While locally available boxes may seem acceptable as substitutes, there are differences in certain critical dimensions. For a fast and easy installation and to avoid costly onsite rework, the user is strongly cautioned to use only Mystery Electronics backboxes. They are proven to be the lowest cost alternative.</p>
Our proprietary ModuLine Insert Panels offer greater connector density in a shallow footprint. Approximately the size of a single gang plate, the mounting configuration provides ample space for 4ea low voltage connectors in a space that a gang plate would only allow 2ea. All XLR type panels (MPK, MPG, MPU) are reversible for either Neutrik D series, or SwitchCraft D3F connectors, and panels are available for decora style active devices as well as Extron AAP and MAAP. Duplex power is available for all FMCA series floor boxes, and utilizes 1ea panel space per power module used.</p>
The Mystery <b>FC8X</b> EasyMix (EM) is a tactical remote control surface for the following digital signal processor (DSP) architectures: Biamp Tesira&reg;, Symetrix SymNet&reg;, and QSC Q-Sys&reg;. There are two models. The <b>FC8X</b> with (8) faders and the FC12X with (12) faders. All communication and controls are bidirectional with touch sensitive motorized faders and backlit buttons. A color HD display is located above each fader to display channel names, live meters, and other custom control functions.</p><p><b><ins>Applications:</b></ins><br />Board Rooms<br />Court Rooms<br />Meeting Rooms<br />Legislative Chambers<br />Training Rooms<br />Auditoriums<br />Stadiums<br />Event Centers</p>
The UL and cUL Listed FMCA2000 raised access floor box assembly combines flexibility, ease of installation, high capacity, and long-term value in an economical floor box assembly.</p><p>Unique design and 12 gauge cover supports loads in excess of the 300lb UL standard. Ideal for classrooms, houses of worship, conference rooms, courtrooms, performance venues or anywhere connections are needed in the floor. The attractive design and finish allows for the FMCA2000 to also be used for in-wall applications.</p>
The UL and cUL Listed FMCA3000 raised access floor box combines flexibility, ease of installation, high capacity, and long-term value in an economical floor box assembly. Proprietary modular panel design accommodates a wide variety of AV connectors, active devices, and barrier separated AC power. The concrete rated rough-in box includes alignment labeling and detailed installation instructions for rough-in installation above grade. Unique design and 12 gauge cover supports loads in excess of the 300lb UL standard. Ideal for classrooms, houses of worship, conference rooms, courtrooms, performance venues or anywhere connections are needed in the floor. The attractive design and finish allows for the FMCA3000 to also be used for in-wall applications.</p>
The UL and cUL Listed FMCA3400 raised access floor box combines flexibility, ease of installation, high capacity, and long-term value in an economical fl oor box assembly. Proprietary modular panel design accommodates a wide variety of AV connectors, active devices, and barrier separated AC power. The concrete rated rough-in box includes alignment labeling and detailed installation instructions for rough-in installation above grade. Unique design and 12 gauge cover supports loads in excess of the 300lb UL standard. Ideal for classrooms, houses of worship, conference rooms, courtrooms, performance venues or anywhere connections are needed in the floor. The attractive design and finish allows for the FMCA3400 to also be used for in-wall applications.</p>