Bullet_point (page 1047 / 1157)

Thread design undercuts to efficiently transfer the load to the base material
Thread form is a 55-degree full profile Whitworth
Thread forming design cold-forms threads in through holes and blind holes without producing chips
Thread has subtle color shading, and stitching detail
Thread length, shank diameter and shank square are made to standard specifications
Thread length, shank diameter and square are made to standard specifications
Thread mills make interrupted cuts and short chips
Thread pitch: 1"-14 UNF
Thread pitch: 1"-8 UNC
Thread pitch: 1/2-13 UNC
Thread pitch: 1/2-20 UNF
Thread pitch: 1/4-20 UNC
Thread pitch: 1/4-28 UNF
Thread pitch: 3/4-10 UNC
Thread pitch: 3/4-16 UNF
Thread pitch: 3/8-16 UNC
Thread pitch: 3/8-24 UNF
Thread pitch: 5/16-18 UNC
Thread pitch: 5/16-24 UNF
Thread pitch: 5/8-11 UNC
Thread pitch: 5/8-18 UNF
Thread pitch: 7/16-14 UNC
Thread pitch: 7/16-20 UNF
Thread pitch: 7/8-9 UNC
Thread pitch: 9/16-12 UNC
Thread rings and setting plugs furnished in Tool Steel 60/62 Rc
Thread rings and setting plugs furnished in Tool Steel, 60/62 Rc
Thread seal tape is recommended for threaded joints
Thread sealant for all services, Lubricates threads for easy assembly
Thread size UNF(M) (port 2) (InchShort): 1/4"-28
Thread size: #10-24
Thread size: #10-32
Thread size: #6-32
Thread size: #8-32
Thread size: 1/2''-13
Thread size: 1/2''-20
Thread size: 1/4''-20
Thread size: 1/4''-28
Thread size: 3/4''-10
Thread size: 3/4''-16
Thread size: 3/8''-16
Thread size: 3/8''-24
Thread size: 5/16''-18
Thread size: 5/16''-24
Thread size: 5/8''-11
Thread size: 7/16''-14
Thread size: 7/16''-20
Thread size: 7/8''-9
Thread size: 9/16''-12
Thread size: 9/16''-18
Thread size: M10
Thread size: M12
Thread size: M20
Thread size: M8
Thread-bound to open flat which helps make reading the contents easy and adds efficiency to note-taking
Thread-in, rubber-capped grate feet offer secure placement within drain channel
Thread: 1/4" NPT
Thread: 1/4"-28
Thread: 2A-UNC
Thread: G1/4"
Threaded
Threaded Inserts
Threaded Inserts (Rivet Nuts)
Threaded Installation
Threaded Opening – Adjust handle (sold separately) placement as needed to extend or reduce reach
Threaded Reducing Flange
Threaded Stud to Clevis Lanyard
Threaded Stud to Threaded Stud Lanyard
Threaded Style
Threaded Top
Threaded adjustment rod and nut provides even tensioning and positions the bearing
Threaded aluminum bypass.
Threaded arbor hole
Threaded at the case head for use with Hornady OAL Gauge
Threaded body allows for fine adjustments in sag
Threaded bonnet for reduced risk of leakage
Threaded bore for fine adjustments, preloading of components, and higher axial loads than smooth bore designs
Threaded bore for fine adjustments, preloading of components, and higher axial loads than smooth bore designs; recessed screw head provides an exterior profile free of major projections for increased safety
Threaded case (NPT)
Threaded connections
Threaded end fitting
Threaded end is chamfered for ease of starting Nut
Threaded end is chamfered for ease of starting nut
Threaded ends comply with ANSI B1.20.1
Threaded for Rigid and IMC Conduits
Threaded for Rigid and IMC condulets, Hex Shoulder
Threaded for easy installation and removal
Threaded hole for attachment to grinding tools
Threaded hole pattern for attachment points
Threaded inserts (for optional leg levelers)
Threaded installation
Threaded on both ends
Threaded ports in BSPP and NPSF
Threaded ports or quick-connect fittings for tubing up to 10 mm in diameter
Threaded pre-load adjusters and machined aluminum spring perches
Threaded pre-load adjusters; machined aluminum spring perches
Threaded shank is for use with threaded-spindle tools, often used in aerospace and automotive applications
Threaded stud and washer in steel, quality class 5.8, blue chromated or stainless steel 1.4305, natural finish
Threaded style contact tip to ensure proper contact with a gas diffuser when installed to the MIG gun
Threaded through holes for a tool stop or coolant through when removed