Brand name: Thomson

Products with this attribute (304 total)

184014R7BM(X)-LFR

22TFNYBUTWNO16ALLS

511H35B0ES2, Profile Rail, 500 Series Ball Carriage, Size: 35 mm, High Precision Grade, B Style, 0 - Clearance Preload, Steel, ES2 - 10mm Dowel Hole - Slip Fit

AFT2-3708, Lead Nut Only, AFT Style, Advanced, 0.375 in X 0.250 in, Anti-Backlash, RH, Acetal, 10 lbf Design Load | Thomson

Ball Bushing bearing pillow blocks are provided with integral, double acting seals that keep out contaminants and retain lubrication, maximizing system performance and life. Twin versions provide up to twice the load capacity or eight times the life of single versions, allowing the use of smaller and less expensive drives, motors and ball screws. When replacing v-ways and flat-ways, the Ball Bushing bearing pillow block?s low coefficient of friction reduces power consumption and provides important design economies.

Bearing Ball Carriage,Height 30.50 mm

Bearing Ball Carriage,Height 35.90 mm

CF322522-4R7K-LFR

ECT09-B43R03PB2510-0299FP00XX, Actuator, Precision, ECT90, brushless AC servo motor, Belt Gear Drive, Parallel, 299 mm Stroke, 10 mm Travel Per Shaft Rev, No Brake, 5800 N

ECT09-B53R01LD2510-0100XN20XX, Actuator, Precision, ECT90, brushless AC servo motor, Direct Drive, Inline, 100 mm Stroke, 10 mm Travel Per Shaft Rev, No Brake, 5300 N

ECT09-B53R03PB3220-0800XQ00XX, Actuator, Precision, ECT90, brushless AC servo motor, Belt Gear Drive, Parallel, 800 mm Stroke, 20 mm Travel Per Shaft Rev, No Brake, 5900 N

ECT09-B53S02PB3220-1500SQ20S1, Actuator, Precision, ECT90, brushless AC servo motor, Belt Gear Drive, Parallel, 1500 mm Stroke, 20 mm Travel Per Shaft Rev, with 24 Vdc Brake, 3900 N, Wash Down Protection

Elektrak HD12B017-0100CNO2EGM - Linear Actuator | Thomson

Elektrak HD12B017-0100CNO2NNS - Linear Actuator | Thomson

Elektrak HD12B017-0100LLX1EES - Linear Actuator | Thomson

Elektrak HD12B017-0100LXP1EES - Linear Actuator | Thomson

Elektrak HD12B017-0200LLX1EES - Linear Actuator | Thomson

EMD250P22M03A000-P3

For end support or intermittent support Shaft support blocks are used for end or intermittent support where loads are light and deflection between supports is not a problem. Unlike shaft support rails, blocks do not permit longitudinal passage of open-type Ball Bushing bearings. Type SB shaft support blocks enable clamping of shafts and eliminate the need for bolts, etc. to maintain shaft position. Shimming is suggested for high precision applications to eliminate the effect of variations in surface of base or manufacturing tolerances between supports.

HC00781225P05, Precision Ball, 5/64 in Diameter, Chrome Steel 52100, Grade 24, P05 Gauge - 100,000 Pieces per Box

HC00937510, Precision Ball, 3/32 in Diameter, Chrome Steel 52100, Grade 10 - 30,000 Pieces per Box, MS19059-1006

HC01562525M05, Precision Ball, 5/32 in Diameter, Chrome Steel 52100, Grade 24, M05 Gauge - 20,000 Pieces per Box

http://cdn.shopify.com/s/files/1/0332/9992/2988/products/49AE68_AW01_1024x.jpg

KGF-N-6310-RH-E-EE, Ball Nut Only, KGF Style, 63 mm X 10 mm, RH, Flange, Wiper, 0.084 Nut Backlash, Maximum, Steel, 76 kN Load, Dynamic | Thomson

KGM-G-3205-RH-E-KK, Ball Nut Only, ZG Style, 32 mm X 5 mm, RH, Wiper, 0.09 Nut Backlash, Maximum, Steel, 23.3 kN Load, Dynamic | Thomson

KGM-G-6310-RH-E-KK, Ball Nut Only, ZG Style, 63 mm X 10 mm, RH, Wiper, 0.18 Nut Backlash, Maximum, Steel, 109.7 kN Load, Dynamic | Thomson

LC1600N24-200380NE, Lifting Column, LC, Lead Screw Drive, 24 Vdc, 200 mm Stroke, 1600 N, Encoder | Thomson

LC1600N24-350581LX, Lifting Column, LC, Lead Screw Drive, 24 Vdc, 350 mm Stroke, 1600 N | Thomson

LC1600N24-400631NE, Lifting Column, LC, Lead Screw Drive, 24 Vdc, 400 mm Stroke, 1600 N, Encoder | Thomson

LC2000N24-276279NX, Lifting Column, LC, Lead Screw, Telescopic Drive, 24 Vdc, 276 mm Stroke, 2000 N | Thomson

LC2000N24-325400NX, Lifting Column, LC, Lead Screw, Telescopic Drive, 24 Vdc, 325 mm Stroke, 2000 N | Thomson

Linear Bearing Annealed Shaft Shaft Dia 1.500 In Dia Tolerance Min 1.499 In Dia Tolerance Max 1.499 In Length 12 In 1566 Carbon Steel Material For Use With Thomson Linear Ball Bushing Bearings

Linear Bearing Tube Shaft Shaft Dia 1.500 In Dia Tolerance Min 1.499 In Dia Tolerance Max 0.150 In Length 12 In 52100 Tubular Material Minimum Surface Hardness 58 Rc For Use With Thomson Linear Ball Bushing Bearings

Linear Pillow Block Bearing Adjustable Bore Dia 1.250 In Overall Width 4.000 In Overall Length 3.630 In Overall Height 1.500 In Body Width 3.000 In Barrel Dia 1.250 In Mounting Surface to Shaft Center 1.500 In Mounting Hole Center 2.000 In Mounting Hole Dia #10 In Dynamic Load Capacity 2350 Lb For Use With Thomson Shafting

Linear Pillow Block Bearing Closed Twin Bore Dia 1.500 In Overall Width 4.750 In Overall Length 9.000 In Overall Height 3.250 In Body Width 3.500 In Flange Thickness 0.500 In Mounting Surface to Shaft Center 1.750 In Mounting Hole Center 4.125 In Mounting Hole Dia 0.280 In 0.250 Bolt Size Static Load Capacity 14 000 Lb For Use With Thomson Shafting

Linear Pillow Block Bearing, Inside Dia. 1/2 in, Material Aluminum, Bearing Type Plain, Body Width (In.) 1.63 in, Color Silver, Dimension a 1.63 in, Dimension A2 1.63 in, Dimension B 1.63 in, Dimension E 1.25 in, Dimension E1 1.25 in, Dimension F1 0.25 in

Linear Support Rail, For Use With Thomson 60 Case Shafting and Linear Bearings, System of Measurement Inch

Made of durable carbon steel, this right-hand thread ball nut is non-preloaded. End block is quick-mount.

MF07K057-A00X074 Linear Motion Systems | Thomson

MG07K057-A00X065, Linear Unit, Movopart M75, Ball Screw Drive, Prism Guide, 0.05 mm Repeatability, Non-Preloaded, 422 mm Stroke, 728 mm Overall Length, Single Standard Carriage, 5 mm Travel Per Shaft Rev, Single Shaft With Keyway, 0.42 m/s Maximum Linear Speed | Thomson

Microstage System, Carriage Material Aluminum Alloy (Anodized), Rail Material 60 Case Shafting, Repeatability -

MLA08A05-0333S0150-C4-S01, Motorized Lead screw Actuator, NEMA 08, 0.001665 in Travel/Step, 1.5 in Stroke, M3x0.5 Male Thread End Mounting, Single Stack, 0.5 A, Actuator | Thomson

MLA08A05-0400S0150-C4-S01, Motorized Lead screw Actuator, NEMA 08, 0.002 in Travel/Step, 1.5 in Stroke, M3x0.5 Male Thread End Mounting, Single Stack, 0.5 A, Actuator | Thomson

MLA11A05-0025VS0250-C2-S02, Motorized Lead screw Actuator, NEMA 11, 0.000125 in Travel/Step, 2.5 in Stroke, #8-32 x 0.265 in Male Thread End Mounting, Single Stack, 0.51 A | Thomson

MLA11A05-0025VS0250-C5-S02, Motorized Lead screw Actuator, NEMA 11, 0.000125 in Travel/Step, 2.5 in Stroke, M4x0.7 x 6.73 mm Male Thread End Mounting, Single Stack, 0.51 A | Thomson

MLN11A05-180050P04000N-C1A0-XXX, Motorized, NEMA 11, 0.00025 in Travel/Step, Single Stack, 0.51 A, Rotating Nut, Nut integral to motor, 0.18 X 0.05 in Lead Screw | Thomson

Motion Industries

Motion Industries

Motion Industries

Motion Industries

Motion Industries