GUHRING INC. Products

All products from this brand (4297 total)

13mm Aero-Tech 3 Flute 45? Helix Carbide Plain Shank End Mill Bright Uncoated, 22mm LOC, 38mm Reach 22MM LOC,13MM SHANK,83MM OAL AERO-TECH / GH 100 U 3 Flute Standard Length, Right Hand 45? Helix, Right Hand Cut, Plain Cylindrical Shank, Center Cutting Carbide End Mill, .15mm x 45? Corner Chamfer, Bright Uncoated. Optimized flute geometry for ultimate efficiency in slot milling and roughing operations in aluminum, alloyed steels, free cutting steels, tool steels, stainless steels, cast iron, brass, bronze, plastics, special alloys & hardened steels to 54 HRc Series 3203 Guhring Part #9032030130000

13mm Carbide 130? 4-Facet Point RT150GG 4xD Straight Flute Coolant Fed Bright Drill, Reinforced Shank, 74mm LOC 74mm LOC,124mm OAL,14mm Shank Series No. 6068, Order Code 13.000, Guhring Part #9060680130000

13mm Carbide 140? Point RT100HF 7xD nano-Si? Coated Coolant Fed Drill, Reinforced Straight Shank, 133mm LOC 133mm LOC,182mm OAL,14mm Shank Series No. 8522, Order Code 13.000, Guhring Part #9085220130000

13mm Carbide 140? Point RT100U 3xD nano-Firex Coolant Fed Drill, Reinforced Whistle-Notch Flat Shank, 60mm LOC 60mm LOC,107mm OAL,14mm Shank Series No. 5610, Order Code 13.000, Guhring Part #9056100130000

13mm Carbide Radius Point RT100R 5xD Firex? Coated Coolant Fed Drill, Reinforced Straight Shank, 77mm LOC 77mm LOC,124mm OAL,14mm Shank Series No. 6501, Order Code 13.000, Guhring Part #9065010130000

13mm Carbide Radius Point RT100R 7xD Firex? Coated Coolant Fed Drill, Reinforced Straight Shank, 133mm LOC 133mm LOC,182mm OAL,14mm Shank Series No. 6502, Order Code 13.000, Guhring Part #9065020130000

13mm Diameter Carbide 140? Point RT100HF 3xD nano-Si? Coated Drill, Reinforced Straight Shank, 60mm LOC 60mm LOC,107mm OAL,14mm Shank Series No. 8524, Order Code 13.000, Guhring Part #9085240130000

13mm Diameter HSS 130? Point GT100 Parabolic Flute Taper Length Drill, TiN Coated, 134mm LOC, 205mm OAL 134mm LOC,205mm OAL,13mm Shank Series No. 668, Order Code 13.000, Guhring Part #9006680130000

13mm Diameter HSS General Purpose 118? Point Angle Jobber Length Drill, TiN Coated, 101mm LOC 101mm LOC,151mm OAL,13mm Shank Series No. 651, Order Code 13.000, Guhring Part #9006510130000

13mm Diameter HSS High Helix 130? Point Taper Length Drill, Bright Finish, 134mm LOC, 205mm OAL 134mm LOC,205mm OAL,13mm Shank Series No. 219, Order Code 13.000, Guhring Part #9002190130000

13mm ER32 GUHRING Collet Sealing Washer For Coolant Pressure Up To 150 Bar, 13.0mm - 12.5mm Sealing Range Collet Sealing Washers Are For Use With Coolant-Through Cutting Tools And Standard ER Collets in Conjunction With Sealed Collet Chucks Which Use IC/ER Collet Nuts Specifically Designed For Use With Collet Sealing Washers. The Washer is First Installed Into a Special Recess Inside The IC/ER Collet Nut, Then The Collet is Installed Into The IC/ER Collet Nut as Usual. ER Collet Sealing Washers Are to be Applied For Tool Shanks Matching The Sealing Washer Nominal Size And 0.5mm Smaller, Down to the Next Size Sealing Washer in the Series. - For Example: to Seal a 3.17mm (1/8\

13mm ER40 Collet, GUHRING High Quality Elastic Spring Steel, Clamping Range is 13mm to 12mm Standard ER Elastic Spring Steel Collets to DIN ISO 15488. ER Collets Are to be Applied For Tool Shanks Matching The Collet Nominal Size And Smaller, Down to the Next Size Collet in the Series. - For Example: to Clamp a 1.59mm (1/16\

13mm Powdered Metal Cobalt 130? Point GT500 Parabolic Flute Jobber Length Drill, TiN Coated, 101mm LOC 101mm LOC,151mm OAL,13mm Shank Series No. 5522, Order Code 13.000, Guhring Part #9055220130000

14 NPT TPI For Minimum Hole 1/2\

14.0mm HT800WP 140? Point Angle nano-Si Coated Carbide Replaceable Tip Drill Insert For Cast Iron Series No. 4113, Order Code 14.000, Guhring Part #9041130140000

14.1mm HT800WP 140? Point Angle Bright Uncoated Carbide Replaceable Tip Drill Insert For Aluminum & Non-Ferrous Metals Series No. 4114, Order Code 14.100, Guhring Part #9041140141000

14.25mm Diameter HSS General Purpose 118? Point Angle Jobber Length Drill, TiN Coated, 114mm LOC 114mm LOC,169mm OAL,14.25mm Shank Series No. 651, Order Code 14.250, Guhring Part #9006510142500

14.25mm HSS General Purpose Morse Taper Shank #2, 118? Point Jobber Length Drill, TiN Coated, 114mm LOC 114mm LOC,212mm OAL,MT2 Shank Series No. 654, Order Code 14.250, Guhring Part #9006540142500

14.3mm Carbide 140? Point RT100VA 3xD nano-A? Coated Coolant Fed Drill, Reinforced Straight Shank, 65mm LOC 65mm LOC,115mm OAL,16mm Shank Series No. 8510, Order Code 14.300, Guhring Part #9085100143000

14.3mm Diameter Carbide 140? Point RT100U 5xD nano-Firex? Coated Drill, Reinforced Straight Shank, 83mm LOC 83mm LOC,133mm OAL,16mm Shank Series No. 5515, Order Code 14.300, Guhring Part #9055150143000

14.4mm Carbide Radius Point RT100R 7xD Firex? Coated Coolant Fed Drill, Reinforced Straight Shank, 152mm LOC 152mm LOC,204mm OAL,16mm Shank Series No. 6502, Order Code 14.400, Guhring Part #9065020144000

14.4mm Diameter HSS 118? Point General Purpose Stub Length Drill, Steam Oxide Finish, 56mm LOC, 111mm OAL 56mm LOC,111mm OAL,14.4mm Shank Series No. 223, Order Code 14.400, Guhring Part #9002230144000

14.4mm HT800WP 140? Point Angle nano-Si Coated Carbide Replaceable Tip Drill Insert For Cast Iron Series No. 4113, Order Code 14.400, Guhring Part #9041130144000

14.50mm - 14.99mm Insert Range, 16mm Shank, HT800WP 10XD Indexable Drill Body, Coolant Fed, Nickel Coated 152.8mm LOC,225mm OAL,16mm Shank Spiral Flute Tool Steel Drill Body with Reinforced Straight Shank and Whistle-Notch Flat per DIN 6535-HE Series No. 4110, Order Code 14.500, Guhring Part #9041100145000

14.50mm - 14.99mm Insert Range, 5/8\

14.5mm Carbide 140? Point RT100HF 3xD nano-Si? Coated Coolant Fed Drill, Reinforced Straight Shank, 65mm LOC 65mm LOC,115mm OAL,16mm Shank Series No. 8520, Order Code 14.500, Guhring Part #9085200145000

14.5mm Coolant Fed Cobalt 130? Point GT80 Parabolic Jobber Drill, Reinforced Shank w/Whistle Notch, Bright Finish 83mm LOC,133mm OAL,16mm Shank Series No. 1131, Order Code 14.500, Guhring Part #9011310145000

14.5mm Diameter Carbide 140? Point RT100U 5xD TiN Coated Drill, Reinforced Straight Shank, 89mm LOC 89mm LOC,151mm OAL,14.5mm Shank Series No. 1243, Order Code 14.500, Guhring Part #9012430145000

14.5mm Diameter HSS General Purpose 118? Point Angle Jobber Length Drill, TiN Coated, 114mm LOC 114mm LOC,169mm OAL,14.5mm Shank Series No. 651, Order Code 14.500, Guhring Part #9006510145000

14.5mm ER32 GUHRING Collet Sealing Washer For Coolant Pressure Up To 150 Bar, 14.5mm - 14.0mm Sealing Range Collet Sealing Washers Are For Use With Coolant-Through Cutting Tools And Standard ER Collets in Conjunction With Sealed Collet Chucks Which Use IC/ER Collet Nuts Specifically Designed For Use With Collet Sealing Washers. The Washer is First Installed Into a Special Recess Inside The IC/ER Collet Nut, Then The Collet is Installed Into The IC/ER Collet Nut as Usual. ER Collet Sealing Washers Are to be Applied For Tool Shanks Matching The Sealing Washer Nominal Size And 0.5mm Smaller, Down to the Next Size Sealing Washer in the Series. - For Example: to Seal a 3.17mm (1/8\

14.5mm ER40 GUHRING Collet Sealing Washer For Coolant Pressure Up To 150 Bar, 14.5mm - 14.0mm Sealing Range Collet Sealing Washers Are For Use With Coolant-Through Cutting Tools And Standard ER Collets in Conjunction With Sealed Collet Chucks Which Use IC/ER Collet Nuts Specifically Designed For Use With Collet Sealing Washers. The Washer is First Installed Into a Special Recess Inside The IC/ER Collet Nut, Then The Collet is Installed Into The IC/ER Collet Nut as Usual. ER Collet Sealing Washers Are to be Applied For Tool Shanks Matching The Sealing Washer Nominal Size And 0.5mm Smaller, Down to the Next Size Sealing Washer in the Series. - For Example: to Seal a 3.17mm (1/8\

14.6mm Diameter HSS 118? Point General Purpose Stub Length Drill, Steam Oxide Finish, 56mm LOC, 111mm OAL 56mm LOC,111mm OAL,14.6mm Shank Series No. 223, Order Code 14.600, Guhring Part #9002230146000

14.75mm Diameter HSS General Purpose 118? Point Jobber Length Drill, Steam Oxide Finish, 114mm LOC, 169mm OAL 114mm LOC,169mm OAL,14.75mm Shank Series No. 205, Order Code 14.750, Guhring Part #9002050147500

14.75mm HSS General Purpose Bushing Length Drill, Morse Taper #2 Shank, 118? Point, Steam Oxide Finish, 147mm LOC 147mm LOC,245mm OAL,MT2 Shank Series No. 257, Order Code 14.750, Guhring Part #9002570147500

14.7mm HT800WP 140? Point Angle nano-A Coated Carbide Replaceable Tip Drill Insert For Stainless Steel Series No. 4115, Order Code 14.700, Guhring Part #9041150147000

14.7mm HT800WP 145? Point Angle nano-A Coated Carbide Replaceable Tip Drill Insert For Pilot Drilling Series No. 4111, Order Code 14.700, Guhring Part #9041110147000

14.8mm Diameter HSS 118? Point General Purpose Stub Length Drill, TiN Coated, 56mm LOC, 111mm OAL 56mm LOC,111mm OAL,14.8mm Shank Series No. 653, Order Code 14.800, Guhring Part #9006530148000

14.8mm HSS General Purpose Morse Taper Shank #2, 118? Point Jobber Length Drill, Steam Oxide Finish, 114mm LOC 114mm LOC,212mm OAL,MT2 Shank Series No. 245, Order Code 14.800, Guhring Part #9002450148000

14mm Carbide 140? Point RT100HF 3xD nano-Si? Coated Coolant Fed Drill, Reinforced Straight Shank, 60mm LOC 60mm LOC,107mm OAL,14mm Shank Series No. 8520, Order Code 14.000, Guhring Part #9085200140000

14mm Carbide 140? Point RT100U 3xD TiN Coated Drill, Reinforced Whistle-Notch Flat Shank, 60mm LOC 60mm LOC,107mm OAL,14mm Shank Series No. 1184, Order Code 14.000, Guhring Part #9011840140000

14mm Carbide 140? Point RT100VA 5xD nano-A? Coated Coolant Fed Drill, Reinforced Straight Shank, 77mm LOC 77mm LOC,124mm OAL,14mm Shank Series No. 8511, Order Code 14.000, Guhring Part #9085110140000

14mm Carbide Radius Point RT100R 5xD Firex? Coated Coolant Fed Drill, Reinforced Straight Shank, 77mm LOC 77mm LOC,124mm OAL,14mm Shank Series No. 6501, Order Code 14.000, Guhring Part #9065010140000

14mm CAT-50 GUHRING Shrink Fit Holder With Conventional Coolant Through, 80mm Gage Length CAT Taper to ANSI / ASME B 5.50 | Coolant Form AD/B | Balanced to G2.5 / 25,000 RPM | For Tool Shank Tolerance h6 | Includes Setting Screw, Series No. 4977 With Axial Force Dampening For Perfect Runout Accuracy | Suitable For Tools With Internal Coolant. A gripping principle: When shrink fitting tools into shrink fit chucks, the decisive factors for ensuring the safe clamping of the tool in the tool holder are solely the heating and cooling of the tool holder. The heating process expands the shrink fit chuck enabling a tool to be inserted or withdrawn respectively. During the cooling process it contracts again and clamps the inserted tool with maximum clamping force. Series No. 4764, Order Code 014.0500. Made in Germany, Guhring Part #9047640140500

14mm Diameter General Purpose Cobalt 118? Point Angle Jobber Length Drill, Steam Oxide Finish, 108mm LOC 108mm LOC,160mm OAL,14mm Shank Series No. 305, Order Code 14.000, Guhring Part #9003050140000

14mm Diameter HSS General Purpose 118? Point Jobber Length Drill, Steam Oxide Finish, 108mm LOC, 160mm OAL 108mm LOC,160mm OAL,14mm Shank Series No. 205, Order Code 14.000, Guhring Part #9002050140000

14mm ER25 Collet, GUHRING High Quality Elastic Spring Steel, Clamping Range is 14mm to 13mm Standard ER Elastic Spring Steel Collets to DIN ISO 15488. ER Collets Are to be Applied For Tool Shanks Matching The Collet Nominal Size And Smaller, Down to the Next Size Collet in the Series. - For Example: to Clamp a 1.59mm (1/16\

14mm High Performance PCD 2FL Coolant Fed Slot Drill For Aluminum & Composites, 16mm LOC, 38mm Reach, 100mm OAL 16MM LOC,14MM SHANK,100MM OAL DL 100 X2 PCD (Polycrystalline Diamond) Coated, Right Hand Cutting, Non-Helical Flutes, Center Cutting Carbide Coolant Fed 2 Flute End Mill or Slot Drill with .10mm Corner Radius, Extended Neck Relief & Plain Cylindrical Shank for High Performance High Speed Slotting, Roughing, Ramping, Plunging, Helical Interpolation, Copy Milling and Finishing Aluminum, Graphite and Composite Materials Series 5493 Guhring Part #9054930140010

14mm High Performance PCD 3FL Coolant Fed Slot Drill For Aluminum & Composites, 16mm LOC, 38mm Reach, 100mm OAL 16MM LOC,14MM SHANK,100MM OAL DL 100 X2 PCD (Polycrystalline Diamond) Coated, Right Hand Cutting, Non-Helical Flutes, Center Cutting Carbide Coolant Fed 3 Flute End Mill or Slot Drill with .10mm Corner Radius, Extended Neck Relief & Plain Cylindrical Shank for High Performance High Speed Slotting, Roughing, Ramping, Plunging, Helical Interpolation, Copy Milling and Finishing Aluminum, Graphite and Composite Materials Series 5496 Guhring Part #9054960140010

14mm I.D. CAT-40 GUHRING Hydraulic Chuck Conventional AD/B Coolant Through, 64mm Gage Length CAT taper to ANSI/ASME B 5.50 coolant form AD/B | balanced to G2.5 / 25,000 RPM | tremendous clamping force | maximum concentricity deviation 3 um | axial length adjustment | for tool shank tolerance h6 | includes adjustment screw, Series no. 4900 | includes hexagon chuck key, Series no. 4912. The use of reduction sleeves greatly improves the usefulness of a hydraulic chuck. Clamp directly on the cutting tool shank or use a reduction sleeve to hold a different diameter tool shank and increase transferable torque by approximately 25%. The reduction sleeve outside diameter must match your hydraulic chuck's nominal inside diameter. Reduction sleeves are available in 6 different O.D.s; 1/2\

14mm I.D. HSK-100A GUHRING Hydraulic Chuck w/Coolant & Radial Accessed Length Adjustment, 95mm Gage Length HSK-A to ISO 12164-1/DIN 69893-1 | balanced to G2.5 / 25,000 RPM | tremendous clamping force | maximum concentricity deviation 3 um | robust, radial operated length adjustment | 10mm length adjustability | for tool shank tolerance h6 | includes hex wrench for radial length setting | includes hexagon chuck key, Series no. 4912 | order coolant supply set 4949 separately. The use of reduction sleeves greatly improves the usefulness of a hydraulic chuck. Clamp directly on the cutting tool shank or use a reduction sleeve to hold a different diameter tool shank and increase transferable torque by approximately 25%. The reduction sleeve outside diameter must match your hydraulic chuck's nominal inside diameter. Reduction sleeves are available in 6 different O.D.s; 1/2\

14mm I.D. HSK-100A GUHRING Shrink Fit Holder With Conventional or MQL Coolant, 160mm Gage Length HSK-A to ISO12164-1 / DIN 69893-1 | Balanced to G2.5 / 25,000 RPM | Includes 4 or 6 M6 Balancing Screws | For Tool Shank Tolerance h6 | to DIN 69882-8 | Includes Setting Screw, Series No. 4977 or 4904 | For Conventional Cooling Order Coolant Supply Set, Series 4949 Separately | Suitable For Tools With Internal Coolant. A gripping principle: When shrink fitting tools into shrink fit chucks, the decisive factors for ensuring the safe clamping of the tool in the tool holder are solely the heating and cooling of the tool holder. The heating process expands the shrink fit chuck enabling a tool to be inserted or withdrawn respectively. During the cooling process it contracts again and clamps the inserted tool with maximum clamping force. Series No. 4736, Order Code 114.1000. Made in Germany, Guhring Part #9047361141000

14mm I.D. HSK-40A GuhrOJet Peripheral Coolant-Fed Shrink Fit Holder, 90mm Gage Length HSK-A to ISO 12164-1 / DIN 69893-1 | Balanced to G2.5 / 25,000 RPM | For Tool Shank Tolerance h6 | to DIN 69882-8 | Includes 4 or 6 M6 Balancing Screws | Optimized For Cutting Tools Without Internal Coolant Ducts | With Coolant Ducts in the Bore For Directing Peripheral Coolant Directly to the Cutting Tool, Improving The Machining Process And Extending Tool Life | Includes Setting Screw, Series No. 4977 With Axial Force Dampening For Perfect Runout Accuracy. A gripping principle: When shrink fitting tools into shrink fit chucks, the decisive factors for ensuring the safe clamping of the tool in the tool holder are solely the heating and cooling of the tool holder. The heating process expands the shrink fit chuck enabling a tool to be inserted or withdrawn respectively. During the cooling process it contracts again and clamps the inserted tool with maximum clamping force. Series No. 4755, Order Code 014.0400. Made in Germany, Guhring Part #9047550140400

14mm I.D. HSK-50A GUHRING Hydraulic Chuck w/Coolant & Increased Clamping Force, 85mm Gage Length HSK-A to ISO 12164-1 / DIN 69893-1 | balanced to G2.5 / 25,000 RPM | tremendous clamping force | maximum concentricity deviation 3 um | extra long gage lengths 150mm & 160mm maximum concentricity deviation 5 ?m and 200mm gage length maximum concentricity deviation 7 ?m | axial length adjustment | for tool shank tolerance h6 | includes adjustment screw, Series no. 4900 | includes hexagon chuck key, Series no. 4912 | order coolant supply set, Series No. 4949 separately. The use of reduction sleeves greatly improves the usefulness of a hydraulic chuck. Clamp directly on the cutting tool shank or use a reduction sleeve to hold a different diameter tool shank and increase transferable torque by approximately 25%. The reduction sleeve outside diameter must match your hydraulic chuck's nominal inside diameter. Reduction sleeves are available in 6 different O.D.s; 1/2\

14mm I.D. HSK-50A GUHRING Whistle Notch Side Lock Holder, Coolant Through, 90mm Gage Length HSK-A to ISO 12164-1 / DIN 69893-1 | Balanced to G6.3 / 15,000 RPM | For Tool Shank to Tolerance h6 | Dimensions to DIN 69882-5 | From Bore Diameter 25mm With Two Clamping Screws | Includes Clamping Screw, Series No. 4903 and Adjustment Screw. Series No. 4334, Order Code 014.0500. Made in Germany, Guhring Part #9043340140500

14mm I.D. HSK-63A GUHRING Hydraulic Chuck w/Coolant & Increased Clamping Force, 150mm Gage Length HSK-A to ISO 12164-1 / DIN 69893-1 | balanced to G2.5 / 25,000 RPM | tremendous clamping force | maximum concentricity deviation 3 um | extra long gage lengths 150mm & 160mm maximum concentricity deviation 5 ?m and 200mm gage length maximum concentricity deviation 7 ?m | axial length adjustment | for tool shank tolerance h6 | includes adjustment screw, Series no. 4900 | includes hexagon chuck key, Series no. 4912 | order coolant supply set, Series No. 4949 separately. The use of reduction sleeves greatly improves the usefulness of a hydraulic chuck. Clamp directly on the cutting tool shank or use a reduction sleeve to hold a different diameter tool shank and increase transferable torque by approximately 25%. The reduction sleeve outside diameter must match your hydraulic chuck's nominal inside diameter. Reduction sleeves are available in 6 different O.D.s; 1/2\

14mm I.D. HSK-63A GUHRING Hydraulic Chuck w/Coolant & Increased Clamping Force, 85mm Gage Length HSK-A to ISO 12164-1 / DIN 69893-1 | balanced to G2.5 / 25,000 RPM | tremendous clamping force | maximum concentricity deviation 3 um | extra long gage lengths 150mm & 160mm maximum concentricity deviation 5 ?m and 200mm gage length maximum concentricity deviation 7 ?m | axial length adjustment | for tool shank tolerance h6 | includes adjustment screw, Series no. 4900 | includes hexagon chuck key, Series no. 4912 | order coolant supply set, Series No. 4949 separately. The use of reduction sleeves greatly improves the usefulness of a hydraulic chuck. Clamp directly on the cutting tool shank or use a reduction sleeve to hold a different diameter tool shank and increase transferable torque by approximately 25%. The reduction sleeve outside diameter must match your hydraulic chuck's nominal inside diameter. Reduction sleeves are available in 6 different O.D.s; 1/2\

14mm I.D. HSK-63A GuhrOJet Peripheral Coolant-Fed Shrink Fit Holder, 120mm Gage Length HSK-A to ISO 12164-1 / DIN 69893-1 | Balanced to G2.5 / 25,000 RPM | For Tool Shank Tolerance h6 | to DIN 69882-8 | Includes 4 or 6 M6 Balancing Screws | Optimized For Cutting Tools Without Internal Coolant Ducts | With Coolant Ducts in the Bore For Directing Peripheral Coolant Directly to the Cutting Tool, Improving The Machining Process And Extending Tool Life | Includes Setting Screw, Series No. 4977 With Axial Force Dampening For Perfect Runout Accuracy. A gripping principle: When shrink fitting tools into shrink fit chucks, the decisive factors for ensuring the safe clamping of the tool in the tool holder are solely the heating and cooling of the tool holder. The heating process expands the shrink fit chuck enabling a tool to be inserted or withdrawn respectively. During the cooling process it contracts again and clamps the inserted tool with maximum clamping force. Series No. 4755, Order Code 214.0630. Made in Germany, Guhring Part #9047552140630

14mm I.D. MAS/BT-40 AD/B GuhrOJet Peripheral Coolant-Fed Weldon Side Lock Holder, 63mm Gage Length MAS/BT to JIS B 6339 | Coolant Form AD/B | Balanced to G6.3 / 15,000 RPM | For Tool Shank Tolerance h6 | Bore to DIN 1835-2 Form \

14mm I.D. MAS/BT-40 GUHRING Whistle Notch Side Lock Holder, Coolant Through, 63mm Gage Length MAS/BT to DIN ISO 7388-2 Form AD/B | With Bore to DIN 1835-2 Form E ?Whistle Notch\

14mm I.D. x 1-1/4\

14mm Straight Flute Carbide 130? Point RT150GG 10xD Coolant Fed Bright Drill, Reinforced Straight Shank, 183mm LOC 183mm LOC,233mm OAL,14mm Shank Series No. 6070, Order Code 14.000, Guhring Part #9060700140000

14mm Uni-Pro 2FL Ball, Necked 30? Helix Std Length Carbide End Mill, Plain Shank, Firex Coated, 22mm LOC, 38mm Reach 22MM LOC,14MM SHANK,83MM OAL UNI-PRO Right Hand 30? Helix, Right Hand Cut, 2 Flute Ball Nose Standard Length Universal General Purpose Center Cutting Carbide End Mill with 38.00mm Extended Neck Relief, Plain Cylindrical Shank, Firex Coated Series 3679 Guhring Part #9036790140000

14mm Uni-Pro 2FL Ball, Necked 30? Helix Std Length Carbide End Mill, Plain Shank, Uncoated, 22mm LOC, 38mm Reach 22MM LOC,14MM SHANK,83MM OAL UNI-PRO Right Hand 30? Helix, Right Hand Cut, 2 Flute Ball Nose Standard Length Universal General Purpose Center Cutting Carbide End Mill with 38.00mm Extended Neck Relief, Plain Cylindrical Shank, Bright Uncoated Series 3308 Guhring Part #9033080140000

14mm Uni-Pro 2FL Necked 30? Helix X-Long Carbide End Mill, Plain Shank, Firex Coated, 65mm LOC, 150mm OAL, 102mm Reach 65MM LOC,16MM SHANK,150MM OAL UNI-PRO Right Hand 30? Helix, Right Hand Cut, 2 Flute Extra Long Length Universal General Purpose Center Cutting Carbide End Mill with .15mm x 45? Corner Chamfer, 102mm Extended Neck Relief, Plain Cylindrical Shank, Firex Coated Series 3021 Guhring Part #9030210140010

14mm Uni-Pro 2FL Necked 30? Std Length Carbide End Mill, Plain Shank, Firex Coated, 22mm LOC, 83mm OAL, 38mm Reach 22MM LOC,14MM SHANK,83MM OAL UNI-PRO Right Hand 30? Helix, Right Hand Cut, 2 Flute Standard Length Universal General Purpose Center Cutting Carbide End Mill with .15mm x 45? Corner Chamfer, 38mm Extended Neck Relief, Plain Cylindrical Shank, Firex Coated Series 3676 Guhring Part #9036760140000

14mm Uni-Pro 2FL Necked 30? Std Length Carbide End Mill, Plain Shank, Uncoated, 22mm LOC, 83mm OAL, 38mm Reach 22MM LOC,14MM SHANK,83MM OAL UNI-PRO Right Hand 30? Helix, Right Hand Cut, 2 Flute Standard Length Universal General Purpose Center Cutting Carbide End Mill with .15mm x 45? Corner Chamfer, 38mm Extended Neck Relief, Plain Cylindrical Shank, Bright Uncoated Series 3303 Guhring Part #9033030140000

14mm Uni-Pro 3FL Necked 30? Std Length Carbide End Mill, Plain Shank, Uncoated, 22mm LOC, 83mm OAL, 38mm Reach 22MM LOC,14MM SHANK,83MM OAL UNI-PRO Right Hand 30? Helix, Right Hand Cut, 3 Flute Standard Length Universal General Purpose Center Cutting Carbide End Mill with .15mm x 45? Corner Chamfer, 38mm Extended Neck Relief, Plain Cylindrical Shank, Bright Uncoated Series 3307 Guhring Part #9033070140000

14mm Uni-Pro 4FL Necked 30? Helix X-Long Carbide End Mill, Plain Shank, Uncoated, 45mm LOC, 150mm OAL, 105mm Reach 45MM LOC,14MM SHANK,150MM OAL UNI-PRO Right Hand 30? Helix, Right Hand Cut, 4 Flute Extra Long Length Universal General Purpose Center Cutting Carbide End Mill with .15mm x 45? Corner Chamfer, 105mm Extended Neck Relief, Plain Cylindrical Shank, Bright Uncoated Series 3012 Guhring Part #9030120140000

14mm Uni-Pro 4FL Necked 30? Stub Length Carbide End Mill, Plain Shank, Firex Coated, 18mm LOC, 75mm OAL, 30mm Reach 18MM LOC,14MM SHANK,75MM OAL UNI-PRO Right Hand 30? Helix, Right Hand Cut, 4 Flute Stub Length Universal General Purpose Center Cutting Carbide End Mill with .15mm x 45? Corner Chamfer, 30mm Extended Neck Relief, Plain Cylindrical Shank, Firex Coated Series 3637 Guhring Part #9036370140000

15.0mm HT800WP 140? Point Angle Bright Uncoated Carbide Replaceable Tip Drill Insert For Aluminum & Non-Ferrous Metals Series No. 4114, Order Code 15.000, Guhring Part #9041140150000

15.1mm HSS General Purpose Morse Taper Shank #2, 118? Point Jobber Length Drill, TiN Coated, 120mm LOC 120mm LOC,218mm OAL,MT2 Shank Series No. 654, Order Code 15.100, Guhring Part #9006540151000

15.1mm HT800WP 140? Point Angle Bright Uncoated Carbide Replaceable Tip Drill Insert For Aluminum & Non-Ferrous Metals Series No. 4114, Order Code 15.100, Guhring Part #9041140151000

15.25mm HSS General Purpose Morse Taper Shank #2, 118? Point Jobber Length Drill, Steam Oxide Finish, 120mm LOC 120mm LOC,218mm OAL,MT2 Shank Series No. 245, Order Code 15.250, Guhring Part #9002450152500

15.25mm HSS General Purpose Morse Taper Shank #2, 118? Point Jobber Length Drill, TiN Coated, 120mm LOC 120mm LOC,218mm OAL,MT2 Shank Series No. 654, Order Code 15.250, Guhring Part #9006540152500

15.2mm Carbide 140? Point RT100U 3xD TiN Coated Drill, Reinforced Whistle-Notch Flat Shank, 65mm LOC 65mm LOC,115mm OAL,16mm Shank Series No. 1184, Order Code 15.200, Guhring Part #9011840152000

15.2mm Diameter HSS 118? Point General Purpose Stub Length Drill, Steam Oxide Finish, 58mm LOC, 115mm OAL 58mm LOC,115mm OAL,15.2mm Shank Series No. 223, Order Code 15.200, Guhring Part #9002230152000

15.2mm HT800WP 140? Point Angle nano-Si Coated Carbide Replaceable Tip Drill Insert For Cast Iron Series No. 4113, Order Code 15.200, Guhring Part #9041130152000

15.3mm Carbide 140? Point RT100HF 3xD nano-Si? Coated Coolant Fed Drill, Reinforced Straight Shank, 65mm LOC 65mm LOC,115mm OAL,16mm Shank Series No. 8520, Order Code 15.300, Guhring Part #9085200153000

15.3mm Carbide Radius Point RT100R 7xD Firex? Coated Coolant Fed Drill, Reinforced Straight Shank, 152mm LOC 152mm LOC,204mm OAL,16mm Shank Series No. 6502, Order Code 15.300, Guhring Part #9065020153000

15.3mm Diameter General Purpose Cobalt 118? Point Angle Jobber Length Drill, Steam Oxide Finish, 120mm LOC 120mm LOC,178mm OAL,15.3mm Shank Series No. 305, Order Code 15.300, Guhring Part #9003050153000

15.3mm HSS General Purpose Morse Taper Shank #2, 118? Point Jobber Length Drill, Steam Oxide Finish, 120mm LOC 120mm LOC,218mm OAL,MT2 Shank Series No. 245, Order Code 15.300, Guhring Part #9002450153000

15.3mm HT800WP 140? Point Angle Bright Uncoated Carbide Replaceable Tip Drill Insert For Aluminum & Non-Ferrous Metals Series No. 4114, Order Code 15.300, Guhring Part #9041140153000

15.4mm Diameter Carbide 140? Point RT100U 3xD nano-Firex? Coated Drill, Reinforced Straight Shank, 65mm LOC 65mm LOC,115mm OAL,16mm Shank Series No. 5514, Order Code 15.400, Guhring Part #9055140154000

15.4mm Diameter HSS General Purpose 118? Point Jobber Length Drill, Steam Oxide Finish, 120mm LOC, 178mm OAL 120mm LOC,178mm OAL,15.4mm Shank Series No. 205, Order Code 15.400, Guhring Part #9002050154000

15.5mm Carbide 130? Point RT150GG 7xD Coolant Fed Straight Flute Drill, Reinforced Straight Shank, 152mm LOC 152mm LOC,204mm OAL,16mm Shank Series No. 6069, Order Code 15.500, Guhring Part #9060690155000