Notes (page 1 / 8)

**PLEASE SPECIFY BORE SIZE WHEN ORDERING
*Brake Hub NOT Included
*Includes ADVANCED DIGITAL KEYPAD
*Includes Assistant Control Panel (Standard)
*Includes Bluetooth Control Panel
*Includes On/Off, Fwd-Off_Rev, Speed Pot
*Keypad NOT Included
1.750 in. white wall.
12 Month Warranty
12-way adjustable coil-over shock.
1pc/1ctn
2 piece line.
3-1/4" from bottom of carb base to the base of the carb neck. Mounting bolt hole pattern is 5-1/8" by 5-5/8"
3/4 middle bench seat with non pleats.
3/4 middle bench seat with standard sewn pleats.
4 ply load rating.
4.00 in. leg lengths.
4.75 in. leg lengths.
56 inch wheel base universal kit. Modification will be required.
56 inch wheel base universal kit. Modification will be required. Steering rack is for right hand drive.
58 inch wheel base universal kit. Modification will be required. Steering rack is for right hand drive.
60 inch wheel base universal kit. Modification will be required.
60 inch wheel base universal kit. Modification will be required. Steering rack is for right hand drive.
8 cylinder set.
8 x 165.1
9-bolt steering wheel adapter.
Accepts 10120 type pad.
All-natural Ingredients. Vegan. Non-GMO. Safe for diabetics.
Aluminum Dayton Pro/Street pinion support.
Angled bed strips must be purchased separately.
Approximate compression 7.83:1 with a 116.9cc head.
Approximate compression 8.69:1 with a 116.9cc head.
Approximate compression ratio 10.34:1 with a 64cc head.
Approximate compression ratio 10.72:1 with a 64cc head.
Approximate compression ratio 11.93:1 with a 64cc head.
Approximate compression ratio 8.39:1 with a 64cc head.
Approximate compression ratio 9.72:1 with a 64cc head.
Approximate compression ratio 9.73:1 with a 64cc head.
Approximate compression ratio for 1968-72, 1977-82 302 CID is 10.14:1. Approximate compression ratio for 1973-76 302 CID is 9.54:1. Approximate compression ratio for 1973-76 289 CID is 9.75:1.
Beadlock ring color matched to wheel color.
Beadlock ring is black.
Bed strip hardware.
Bed to frame hardware.
Bench back is split 1/3-2/3. No heat seam lines.
Bench back is split 1/3-2/3. Vertical heat seam lines.
Best suited for large displacement, high RPM engine applications.
Black accent grommet with blue insert.
Black accent grommet with red insert.
Black accent grommet with white insert.
Black beadlock ring.
Black cap, gun metal gray powdercoated base.
Black grommets with black inserts and white stripes.
Black stitching with black grommets and black inserts.
Black stitching with brass grommets and black inserts.
Black stitching with steel grommets and black inserts.
Black stitching.
Blue line.
Blue stitching with black grommets and blue inserts.
Blue stitching with brass grommets and blue inserts.
Blue stitching with steel grommets and blue inserts.
Blue stitching.
Blue stitching. For use on models with air bags in the seats.
Brake lines over 6 ft. in length are shipped with a large u-bend and should not be considered defective.
Brake rotor bolt pattern is 5 x 4.750 in. Includes an adjustable proportioning valve.
Brass accent grommet with blue stitching.
Brass accent grommet with gray insert.
Brass grommets with black inserts and white stripes.
Built in the USA
Cabin kit includes mats for all four doors, roof, floor boards, firewall, trunk, and rear pillars
Cable
Cargo area cushion for camper models with air conditioning.
Cargo area cushion for camper models without air conditioning.
Cargo area cushion for camper models.
Center dash panel.
Center gauge panel.
Chain
Chair Seat Cushion - Standard
Charcoal Tint
Cheek pads are removable. top and back linings are not.
Clearance from back of pump to engine block mount is .88"
Comes with 2" end brackets. See installation instructions for adapting 3" belt to 2" bracket.
Compatible with BMW & Mercedes Benz caps.
Complete hardware kit.
Connecting rods include ARP 8740 rod bolts.
Control arms are narrowed 5/8 in.
Control arms are narrowed 5/8 in. Does not include air management.
Convertible models only.
Coupe models only.
Current tripping type
Curved-style lens.
Custom order, requires specification sheet to be filled out before ordering.
Custom pistons are required when using connecting rods with any length other than OE length.
Custom pistons are required when using connecting rods with any length other than OE.
Customers must call to order and specify what top and side colors they want for the cover.
Customization is available for this product, please call to order.
DOM tubing.
DOT
Dash gauge panel.
Dash gauge panel. Speedometer sender is sold separately.
Dash gauge panel. Speedometer sender sold separately.