Comment (page 2 / 2)

Molded part has hot-melt adhesive preinstalled.
No center hold-down.
No center terminal
Non-Impedance Matched and 50 Ohm are not intermatable.
Not approved for reconnection of residential aluminum branch circuit wiring.
One piece - Clam Shell.
Open Frame
Other options available upon request, consult our Product Information Center.
Overall insulation crimp diameter, including crimp barrel, must not exceed 3.18 [.125].
Overall insulation crimp diameter, including crimp barrel, must not exceed 3.18 [.125]., PRO-CRIMPER II
Package
Pin headers in 10- and 14-position sizes have only one slot for snap-in polarizer (military polarization), located as shown.
Plug assemblies for round cable need a top shield, bottom shield, boot, and ferrule.
Plugs are preloaded with size 20 DF posted pin contacts
Pocket Tape
Process seal meets MIL-STD-202, Method 112 test cond. A & D at 85?C.
Receptacle Connector
Recommended applications: Fast Ethernet, 10Base-T Ethernet, and 10/100 Base-T Ethernet (Cat 5 on two pair 1/2, 3/6).
Refer to AMPMODU contacts for crimp snap-in replacement receptacle or pin contacts.
Row Configuration 5+2
SPIRAP Hand Tool is included with each box.
Shipper quantity = 20 X QTY/Plastic box
Single door consoles have a IP66 protection degree whereas double door consoles have a IP 55 protection degree.
Single magnet wire only.
Slide on from front.
Small footprint. VDE rated at 10 amps.
Solder Dipped.
Soldering in "off" position only
Solid or overcoated stranded lead wire only., Two magnet wires may be terminated in the same terminal slot if diameters are equal.
Straight
Strain reliefs are available and may be purchased separately.
Stranding must be split for 8 AWG wire.
Strip
Tape & Reel
The enclosure's front opening needs to be fully covered by using specified parts, such as partial doors, DP, or partial panels, DPP, in order to achieve the stated protection degree.
The floor standing enclosure lift handle LLH, needs to be used in order to mount the locking inserts and cylinders.
The mounting plate, BMP, and DIN profiles, BDR, mounted on profiles, BPP, have to be ordered separately, in order to complete the installation of the terminal box.
The panels are to be mounted onto a fix system front frame (MSFCP) or onto modular system frames (MSMSF or MSMSM).
These contacts can be used in MultiMate contact positions of all connector housings.
These contacts can be used in either Mini-Universal MATE-N-LOK 2 Plug or Cap housings ONLY.
Tin Plate per ASTM B-545
To adjust the mounting plate in depth, depth adjustment brackets (MSMPA) are required.
To minimise how much energy the cooling unit consumes, it is recommended to install the door switch, DSW01. Once installed, the door switch will turn the cooling unit off, once the door is opened.
Tolerance 0.2nH.
Top spun aluminum inlay
Tube
Two magnet wires may be terminated in the same terminal slot if diameters are equal.
Two receptacle connectors are applied per holder.
Two required., Use turnable jackscrews on mating housings when mating to grounding block.
Type 1
UL 94V-0
UL available when ordering - consult factory.
Unit Accepts 1.14[.045] Square or Round Post, Accepts Keying Plug 640254-1and 640255-1
Use Extraction Tool No. 91092-1 for round wire contacts.
Use Extraction Tool No. 91093-1 for round wire contacts.
Use only with -51 molded parts and NT-FR tubing.
Use only with DR-25 tubing.
Use these contacts only with the Standard connectors. Do not use with Blindmate connectors.
Use with accessory GA310, mating connector 36", 18 AWG
Used for field repair or wire gauge change.
Vacuum pick-up button.
Voltage Fixed
Voltage Selectable
Well suited for emergency shut-off, machine control, elevator and escalator control, light barrier control
Wire insulation diameter is limited by the connector housing cavity and clearance for the insertion/extraction tool.
Wire lug terminals accept two No. 20 AWG wires.
Wire strip length-- 3.96 [.156] for all wire sizes.
Wire-to-Board applications
With IEC Class 5 conductor
With locking lance.
With wire protector.
X Level Testing
Y Level Testing