Studio: ['ESE']

Products with this attribute (5 total)

The <strong>LX-5112U</strong> is a Wall Mount Analog Clock with a 12" viewing diameter. The LX-5112U is designed to operate as a Time Code Reader or Stand-Alone Clock. It can read, decode and display time information from most any Master Clock or other source of time code. The clock will display time as received from a source of SMPTE/EBU, ASCII (format 0, 1, 8 or A) or ESE Time Code. After a very simple "set-up" procedure and receipt of time code, the unit automatically sets itself to the exact time and continuously slaves to the time code (If time code is lost, an error indicator is lit and the clock continues counting while referencing an internal crystal time base).</p><p>In absence of external Time Code the unit may be set to real time and allowed to run based on its internal crystal oscillator. The second hand is completely silent and can be programmed for "Sweep" mode or "Step" mode. The initial set-up allows the unit to have its hours (and/or minutes) offset to that of another time zone. Also, since the clock can continuously track time code, there is no need to twice annually compensate for daylight saving time (assuming the Master Clock automatically adjusts itself accordingly).</p>
The <strong>LX-5116U</strong> is a Wall Mount Analog Clock with a 16" viewing diameter. The LX-5116U is designed to operate as a Time Code Reader, Stand-Alone Clock or Impulse Clock. It can read, decode and display time information from most any Master Clock or other source of time code. A rear-mounted DIP switch permits the clock to display time as received from a source of SMPTE/EBU, ASCII or ESE Time Code (the Impulse Clock mode may be replaced with an IRIG-B input mode as a factory option). After a very simple "set-up" procedure and receipt of time code, the unit automatically sets itself to the exact time and continuously slaves to the time code (If time code is lost, an error indicator is lit and the clock continues counting while referencing an internal crystal time base).</p><p>Other user defined modes of operation allow the LX-5116U to be synchronized to a Master Clock with a 1 PPS alternating 12 or 24 VDC "Favag" type output or to be set to real time and allowed to run based on its internal crystal oscillator. The second hand is completely silent and can be programmed for "Sweep" mode or "Step" mode. The initial set-up allows the unit to have its hours (and/or minutes) offset to that of another time zone. Also, since the clock can continuously track time code, there is no need to twice annually compensate for daylight saving time (assuming the Master Clock automatically adjusts itself accordingly).</p>
The ES-250 is an RS-232-C Isolation and Distribution Amplifier. Three 1 x 8 amplifier circuits allow the incoming signal to be distributed via the 24 outputs. The unit receives RS-232-C and buffers the signal so that each of the 24 outputs can drive a single ?user? at a distance of up to 50 feet (per output). All inputs and outputs are via rear mounted terminal block connectors. The two main purposes of the ES-250 are to: <br />1) improve the distribution capabilities of RS-232-C<br />2) provide isolation between users of RS-232-C</p>
The ES-71 converts SMPTE/EBU LTC code or ESE Time Code to a USB interface. The device is powered by the USB interface and is intended for computer time synchronization. The unit features four modes of operation, which may be selected by DIP switch or by software: ESE Time Code, or LTC Real Time with 3 selectable date formats (Leitch, SMPTE 309M or ESE). </p>
The ESE <b>943U-CW</b> is time code display with 4 inch bright Red LED display and ceiling wall mount. The unit is housed in a black-textured aluminum wall-mount enclosure (7" H x 26" W x 3.5" D). The unit accepts, via the rear-mounted terminal block, either ESE Time Code&trade; (TC76&trade;, TC89&trade;, or TC90&trade;), SMPTE/EBU Time Code (Time of Day only) or RS-232C ASCII Time Code(format "0", "1" or "A" at 9600 baud). The ES-943U will automatically determine which code is being received. A rear-mounted DIP switch is used to configure the display for 12 or 24 Hour format, or to display the Date instead of time-of-day (if incoming time code contains Date information, such as ESE TC90, date-encoded SMPTE/EBU or ASCII formats "1" or "A"). If the Time Zone option is ordered, a rear-accessible DIP switch is installed for this function. If receiving ESE Time Code&trade; from a timer, the unit will display Minutes, Seconds and Tenths of Seconds (if the timer has the Tenths option).</p>