ESE Products

All products from this brand (12 total)

Buy the ESE ES-166UP-B, 1" Rack-Mount Time Code Display, Black at Full Compass Systems. 0% Financing and Free Shipping on thousands of items!

The <strong>ES 246/XLR/J</strong> is an ES-246 Audio Distribution Amplifier with XLR Connectors and the 220 VAC/50 Hz Operation option. This unit that accepts a balanced or unbalanced audio signal and produces exact copies of that signal. The outputs are isolated and have recessed gain controls. All inputs and outputs are accessible on terminal blocks for simple "permanent" installations. Or, if option "XLR" is specified, all inputs and outputs are available on XLR connectors for easy disconnect/reconnect. This unit is configured to operate from 220 VAC line voltage. The terminal blocks of this unit are replaced with XLR connectors (the enclosure is doubled in height).</p>

The <strong>LX-220A</strong> provides a convenient source of composite black-burst for preblacking tapes or for synchronization purposes. Eight isolated outputs are provided on rear mounted BNC connectors. The output signal consists of sync, blanking, reference black setup level and color burst which is SCH phased. The LX-220A employs a temperature-compensated crystal oscillator for high stability. A sinewave tone, at 0 dbm (2.2 vpp), is accessible on the rear-mounted RCA connector. The frequency of the tone is selectable (400 Hz or 1 KHz) with a front panel DIP switch. The other front panel DIP switch allows the unit to be switched between NTSC (RS-170A) and PAL composite video.</p><p>The P option is a 19" Front Panel (Rack Mount): Designed for mounting into a standard equipment rack. Panel is 1/8" black anodized Aluminum and chassis is 5" - 10" deep.</p>

The <strong>LX-5112U</strong> is a Wall Mount Analog Clock with a 12" viewing diameter. The LX-5112U is designed to operate as a Time Code Reader or Stand-Alone Clock. It can read, decode and display time information from most any Master Clock or other source of time code. The clock will display time as received from a source of SMPTE/EBU, ASCII (format 0, 1, 8 or A) or ESE Time Code. After a very simple "set-up" procedure and receipt of time code, the unit automatically sets itself to the exact time and continuously slaves to the time code (If time code is lost, an error indicator is lit and the clock continues counting while referencing an internal crystal time base).</p><p>In absence of external Time Code the unit may be set to real time and allowed to run based on its internal crystal oscillator. The second hand is completely silent and can be programmed for "Sweep" mode or "Step" mode. The initial set-up allows the unit to have its hours (and/or minutes) offset to that of another time zone. Also, since the clock can continuously track time code, there is no need to twice annually compensate for daylight saving time (assuming the Master Clock automatically adjusts itself accordingly).</p>

The <strong>LX-5116U</strong> is a Wall Mount Analog Clock with a 16" viewing diameter. The LX-5116U is designed to operate as a Time Code Reader, Stand-Alone Clock or Impulse Clock. It can read, decode and display time information from most any Master Clock or other source of time code. A rear-mounted DIP switch permits the clock to display time as received from a source of SMPTE/EBU, ASCII or ESE Time Code (the Impulse Clock mode may be replaced with an IRIG-B input mode as a factory option). After a very simple "set-up" procedure and receipt of time code, the unit automatically sets itself to the exact time and continuously slaves to the time code (If time code is lost, an error indicator is lit and the clock continues counting while referencing an internal crystal time base).</p><p>Other user defined modes of operation allow the LX-5116U to be synchronized to a Master Clock with a 1 PPS alternating 12 or 24 VDC "Favag" type output or to be set to real time and allowed to run based on its internal crystal oscillator. The second hand is completely silent and can be programmed for "Sweep" mode or "Step" mode. The initial set-up allows the unit to have its hours (and/or minutes) offset to that of another time zone. Also, since the clock can continuously track time code, there is no need to twice annually compensate for daylight saving time (assuming the Master Clock automatically adjusts itself accordingly).</p>

The ES-166UE is a Time Code display featuring 1" Blue LED displays. The unit accepts, via the rear-mounted BNC connector, either ESE Time CodeT (TC76T, TC89T, or TC90T) or SMPTE/EBU Time Code (Time of Day only). RS-232C ASCII Time Code (format "0", "1" or "A" at 9600 baud) may be input via the rear-mounted 9-pin connector.</p><p>The ES-166UE will automatically determine which code is being received. An internal DIP switch is used to configure the display for 12 or 24 Hour format, or to display the Date instead of time-of-day (if incoming time code contains Date information, such as ESE TC90, date-encoded SMPTE/EBU or ASCII formats "1" or "A").</p><p>If the Time Zone option is ordered, an internal DIP switch is installed for this function. If receiving ESE Time CodeT from a timer, the unit will display Minutes, Seconds and Tenths of Seconds (if the timer has the Tenths option).</p><p>The unit may be housed in one of several enclosures: the black anodized aluminum case (ES-166UE); the more rugged baked-powdercoat aluminum case (LX-166U); a 19" x 3.5" panel/chassis (ES-166UEP) or a wall-mount case (ES-166UE/Wall).</p><p><br />Viewing <br />Distance: 35'<br />Time Code Input: ESE, SMPTE/EBU, ASCII<br />Options: ESE, J, NTP-C, NTP-C/PoE, P, P2, PoE, Q, RS, TZ,UL,W, Wall</p><p><br />This unit includes the following options: <br /><b>NTP-C</b> - NTP Client: NTP Client Displays synchronize exclusively with an NTP server (replaces all standard inputs).<br /><b>Blue:</b> Blue LED Displays.<br /><b>P:</b> 19" Front Panel (Rack Mount): Designed for mounting into a standard equipment rack. Panel is 1/8" black anodized Aluminum and chassis is 5" - 10" deep.<br /><b>PoE:</b> Receives 48V operating power via Ethernet cable.</p>

The ES-250 is an RS-232-C Isolation and Distribution Amplifier. Three 1 x 8 amplifier circuits allow the incoming signal to be distributed via the 24 outputs. The unit receives RS-232-C and buffers the signal so that each of the 24 outputs can drive a single ?user? at a distance of up to 50 feet (per output). All inputs and outputs are via rear mounted terminal block connectors. The two main purposes of the ES-250 are to: <br />1) improve the distribution capabilities of RS-232-C<br />2) provide isolation between users of RS-232-C</p>

The ES-299E provides a practical method of putting accurate time information onto a network. The unit reads IRIG A, B, E and NASA36 time codes (Carrier or TTL). The NTP output is provided on a 10/100 Base-T Ethernet connector. The ES-299E is housed in a rugged black anodized desktop enclosure. A voltage-controlled temperature-compensated crystal oscillator is used to maintain the accuracy of the time code outputs when lock is lost. </p><p>The ES-299E is an IPV4/IPV6 compatible NTP Time Server. NTP clients can authenticate the NTP server with MD5 or SHA1 Symmetric Key Authentication. SNMP V1, V2 and V3 support allows specified users to be notified if a cold boot occurs, if Time Code Lock is lost or gained, or if NTP Authentication failed. The web server of the ES-299E can operate in two modes: HTTP or HTTPS. The HTTPS mode has the advantage of all information going to and coming from the server being encrypted.</p>

The ES-71 converts SMPTE/EBU LTC code or ESE Time Code to a USB interface. The device is powered by the USB interface and is intended for computer time synchronization. The unit features four modes of operation, which may be selected by DIP switch or by software: ESE Time Code, or LTC Real Time with 3 selectable date formats (Leitch, SMPTE 309M or ESE). </p>

The ESE <b>943U-CW</b> is time code display with 4 inch bright Red LED display and ceiling wall mount. The unit is housed in a black-textured aluminum wall-mount enclosure (7" H x 26" W x 3.5" D). The unit accepts, via the rear-mounted terminal block, either ESE Time Code™ (TC76™, TC89™, or TC90™), SMPTE/EBU Time Code (Time of Day only) or RS-232C ASCII Time Code(format "0", "1" or "A" at 9600 baud). The ES-943U will automatically determine which code is being received. A rear-mounted DIP switch is used to configure the display for 12 or 24 Hour format, or to display the Date instead of time-of-day (if incoming time code contains Date information, such as ESE TC90, date-encoded SMPTE/EBU or ASCII formats "1" or "A"). If the Time Zone option is ordered, a rear-accessible DIP switch is installed for this function. If receiving ESE Time Code™ from a timer, the unit will display Minutes, Seconds and Tenths of Seconds (if the timer has the Tenths option).</p>

The ESE <strong>ES-976/NTP-C</strong> is an NTP Time Display featuring 7" high red LED displays. The unit is housed in a black-textured aluminum wall-mount enclosure (9" H x 43" W x 3.5" D). The unit accepts an Ethernet connection via the rear-mounted RJ-45 connector and is set to synchronize with an NTP server. All setup features (IP address, time zone offset, etc.) are configured through a Web Page Control Panel interface.</p>

The HD-266/SD/1 is an HD & SD Timecode driven Time & Date Video Inserter, with rackmount. The unit reads ESE Time Code, SMPTE/EBU LTC, D-VITC or RP-188 and synchronizes its internal clock to the timecode reference. The time is inserted onto an SDI video signal. Additionally, up to 30 characters of user defined text may be inserted into the video. Two independent character windows are available and can be used to insert Time, Date, Time & Date and/or User Defined Text. If using ESE Timecode from a Timer product, the unit will automatically switch to Timer display if one of the Time/Date formats are selected. Ten different font sizes are available and the characters may be located anywhere on the video using the horizontal & vertical controls. Included font colors are Grayscale along with six solid colors (Red, Orange, Yellow, Green, Blue & Violet). </p><p> The unit is easily configured using the front panel controls or the front panel mounted USB port with the supplied PC software. The front panel controls consist of four push buttons used to navigate the various setup menus that are displayed on a 16 x 2 character LCD display. The USB port and the PC software provide a user-friendly GUI (Graphical User Interface) used to configure the unit. </p><p> The HD-266/SD/1 may be ordered with up to six independent video channels. Additionally, versions that read other timecodes are available (HD-455/SD/1 reads and displays SMPTE/EBU timecode with Frames for editing purposes and HD-275/SD/1 & HD-277/SD/1 read IRIG timecode).</p>